Emerson Unidrive HS72 Control Getting Started Manual Download Page 18

Page: 18 / 46

Unidrive M702 / HS72 Control Getting Started Guide

Issue Number: 2

4.6

Advanced menus

The advanced menus consist of groups or parameters appropriate to a specific function or feature of
the drive. Menus 0 to 41 can be viewed on the KI-Keypad.

Table 4-2 Advanced menu descriptions

*Only displayed when the option modules are installed.

Menu

Description

Commonly used basic set-up parameters for quick / easy programming

Frequency / Speed reference

Ramps

Frequency slaving, speed feedback and speed control

Torque and current control

Motor control

Sequencer and clock

Temperature monitoring

Digital I/O

Programmable logic, motorized pot, binary sum, timers and scope

Status and trips

Drive set-up and identification, serial communications

Threshold detectors and variable selectors

Standard motion control

User PID controller

Option module slot 1 set-up menu

Option module slot 2 set-up menu

Option module slot 3 set-up menu

General option module application menu 1

General option module application menu 2

General option module application menu 3

Second motor parameters

Menu 0 set-up

Not allocated

Ethernet module (slot 4) set-up menu

Option module slot 1 application parameters

Option module slot 2 application parameters

Option module slot 3 application parameters

Option module slot 4 application parameters

29 Reserved

Onboard user programming application menu

31-41

Advanced motion controller setup parameters

Slot 1

Slot 1 option menus*

Slot 2

Slot 2 option menus*

Slot 3

Slot 3 option menus*

Slot 4

Ethernet menus

Unidrive M702_HS72 Control GSG Iss2.book Page 18 Friday, December 12, 2014 1:05 PM

Summary of Contents for Unidrive HS72















































Search results

Summary of Contents for Unidrive HS72

Reviews:

Related manuals for Unidrive HS72

Brands by name

Popular brands

Emerson Unidrive HS72, Control Getting Started Manual

Search results

Summary of Contents for Unidrive HS72

Reviews:

Related manuals for Unidrive HS72

Brands by name

Popular brands