Emerson Rosemount WPG Reference Manual Download Page 30

Page: 30 / 70

Reference Manual

00809-0100-4045, Rev AB

Configuration

March 2016

Configuration

See

Local device status and notifications

for more information.

From the

HOME

screen, enter the Fast Key sequence

From the

Home

screen, select

2: Configure

Select

2: Advance Setup

Select

1: Measurements

Select

1: Dial/Pressure

Select

3: Over-Press Ind

Follow the commands to perform the procedure.

Note

When the parameter has been set to activate, the notification must be acknowledged and
cleared for the device to return to normal operation.

Measured process

pressure

Parameter Configuration

Unlatched (factory default)

Latched

>105% MWP

LED Color: Green

Dial Location: Off-scale

LED Color: Red

Dial Location: Red X

Fast Keys

2, 2, 1, 1, 3

Table 3-3. Dial Locations

Summary of Contents for Rosemount WPG







































































Search results

Summary of Contents for Rosemount WPG

Reviews:

Related manuals for Rosemount WPG

Brands by name

Popular brands

Emerson Rosemount WPG, Reference Manual

Search results

Summary of Contents for Rosemount WPG

Reviews:

Related manuals for Rosemount WPG

Brands by name

Popular brands