Emerson Rosemount WPG Reference Manual Download Page 22 | Manualshive

Page: 22 / 70

background image

16

Reference Manual

00809-0100-4045, Rev AB

Configuration

March 2016

Configuration

3.3

System readiness

3.3.1

Confirm correct device driver

Verify the latest Device Description (DD/DTM) is loaded on your systems to ensure proper
communications.

1.

Download the latest DD at EmersonProcess.com or

hartcomm.org

.

2.

In the

Browse by Member

dropdown menu, select Rosemount business unit of

Emerson Process Management

.

3.

Select desired product.

a.

Within

Table 3-1

, use the HART Universal Revision and Device Revision numbers to

find the correct Device Description.

Table 3-1. Rosemount Wireless Pressure Gauge Device Revisions and Files

3.4

Configuration basics

3.4.1

Configuration tools

Configuration requires a Field Communicator, AMS Device Manager, or any

Wireless

HART

®

Communicator. Connect the Field Communicator leads to the terminals labeled “COMM”
on the front of the device (see

Figure 2-1

).

NOTICE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions: This device may not cause harmful interference. This device must accept
any interference received, including interference that may cause undesired operation.
This device must be installed to ensure a minimum antenna separation distance of
20 cm (8 in.) from all persons.

Identify device

Find device driver

Review

instructions

Review

functionality

Software

release date

NAMUR

software

revision

(1)

1.

NAMUR Software Revision is located on the hardware tag of the device.

HART

software

revision

(2)

2.

HART Software Revision can be read using a HART capable configuration tool.

HART

universal

revision

Device

revision

(3)

3.

Device Driver file names use Device and DD Revision, e.g. 10_01. HART Protocol is designed to enable legacy device driver revisions to continue to
communicate with new HART devices. To access new functionality, the new Device Driver must be downloaded. It is recommended to download new
Device Driver files to ensure full functionality.

Manual

document

number

Changes to

software

January 2016

1.0.0

3

7

1

00809-0100-

4045

Initial release

«
...
20
21
22
23
24
...
»

Summary of Contents for Rosemount WPG







































































Reviews:

No comments

Related manuals for Rosemount WPG

Brand: Kanomax Pages: 26

Brand: Macnaught Pages: 20

Brand: Landis+Gyr Pages: 54

Brand: Kane Pages: 16

Brand: Bacharach Pages: 48

Brand: Bacharach Pages: 24

Brand: Macnaught Pages: 14

Brand: jenway Pages: 52

Brand: JENCO Pages: 13

Brand: E-Mon Pages: 72

Brand: Hilti Pages: 146

Frontline 802.11

Brand: Teledyne Lecroy Pages: 223

Brand: Lutron Electronics Pages: 20

Brand: Rion Pages: 4

Brand: Water I.D. Pages: 56

Brand: Meec tools Pages: 23

NetSure M832DNA

Brand: Vertiv Pages: 176

Intelligizer Fence Monitor

Brand: Zareba Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands