manualshive.com logo in svg

Emerson Rosemount 8732E, Quick Installation Manual

Share
Download
Emerson Rosemount 8732E Quick Installation Manual Download Page 25

Quick Installation Guide

00825-0100-4662, Rev CC
December 2012

Rosemount 8732

25

S

TEP

 6 

CONTINUED

...

8732E Power Supply

For AC power applications (90-250 VAC, 50-60 Hz) connect AC Neutral to terminal 9 (AC 
N/L2) and connect AC Line to terminal 10 (AC/L1). For DC power applications connect 
negative to terminal 9 (DC -) and positive to terminal 10 (DC +). Units powered by 12-42 V 
DC power supply may draw up to 1 amp of current. See Figure 21 for terminal block 
connections.

Cover Jam Screw

For transmitter housings shipped with a cover jam screw, the screw should be properly 
installed once the transmitter has been wired and powered up. Follow these steps to install 
the cover jam screw:

1. Verify that the cover jam screw is completely threaded into the housing.
2. Install the transmitter housing cover and verify that the cover is tight against the housing.

3. Using an M4 hex wrench, loosen the jam screw until it contacts the transmitter cover.

4. Turn the jam screw an additional 

1

/

2

 turn counterclockwise to secure the cover. 

(Note: Application of excessive torque may strip the threads.)

5. Verify that the cover cannot be removed.

Figure 21.  8732E Transmitter Power Connections

4662RevCCQIG.fm  Page 25  Thursday, January 10, 2013  5:11 PM

Summary of Contents for Rosemount 8732E







































Reviews:

No comments

Brands by name

Popular brands

Load more brands