manualshive.com logo in svg

Emerson Rosemount 585 Annubar, Quick Installation Manual

Share
Download
Emerson Rosemount 585 Annubar Quick Installation Manual Download Page 16

Quick Installation Guide

00825-0200-4585, Rev AA

January 2009

Flanged Flo-Tap 585 Annubar 

16

S

TEP

 9: R

ETRACTING

 

THE

 A

NNUBAR

Gear Drive (G)

1. Remove the drive lock pin.
2. Rotate the crank counter-clockwise. If a power drill with an adapter is used, do not 

exceed 200 rpm.

3. Retract until the rod end nuts are against the gear box mechanism.

P

RODUCT

 C

ERTIFICATIONS

Product Certifications

Approved Manufacturing Locations

Rosemount Inc. — Chanhassen, Minnesota  USA

European Directive Information

The EC declaration of conformity for all applicable European directives for this product can 
be found on the Rosemount website at www.rosemount.com. A hard copy may be obtained 
by contacting our local sales office.

European Pressure Equipment Directive (PED) (97/23/EC)

Rosemount 585 Annubar — Refer to EC declaration of conformity for conformity 
assessment
Pressure Transmitter — See appropriate Pressure Transmitter QIG

Hazardous Locations Certifications

For information regarding the transmitter product certification, see the appropriate 
transmitter QIG:

• Rosemount 3051S (document number 00825-0100-4801)
• Rosemount 3095M (document number 00825-0100-4716)

4585_0200_QIG_AA.fm  Page 16  Thursday, January 29, 2009  3:05 PM

Summary of Contents for Rosemount 585 Annubar

















Reviews:

No comments

Brands by name

Popular brands

Load more brands