Emerson Rosemount 3051S Series Quick Installation Manual Download Page 17 | Manualshive

Page: 17 / 36

background image

Quick Installation Guide

00825-0100-4801, Rev HA
February 2008

Rosemount 3051S

17

S

AFETY

I

NSTRUMENTED

S

YSTEMS

Additional Safety Instrumented Systems information is available in the
Rosemount 3051S reference manual (document number
00809-0100-4801). The manual is available electronically on
www.rosemount.com or by contacting an Emerson Process
Management representative.

3051S Safety-Certified Identification

All 3051S transmitters must be identified as safety-certified before
installing into SIS systems.

NOTE

There are two versions of safety-certified 3051S pressure transmitters.
For transmitters with a yellow SIS circuit board installed and output
code B in the model number, please refer to Manual Supplement
00809-0700-4801.

To identify a safety-certified 3051S:

1. Connect a HART host to the transmitter.
2. Check the software to verify that the software revision is 7 or

higher.

Fast Key Sequence - 1, 5

3. Verify that option code QT is included in the transmitter model

code.

Revision #’s

Fld Dev Rev

7

Software Rev

7

Hardware Rev

16

4801_QIG_RevHA.fm Page 17 Tuesday, February 26, 2008 12:17 PM

«
...
15
16
17
18
19
...
»

Summary of Contents for Rosemount 3051S Series





































Reviews:

No comments

Related manuals for Rosemount 3051S Series

Brand: Darfon Pages: 28

Brand: VanEssa mobilcamping Pages: 8

Brand: Yakima Pages: 11

Brand: Jabra Pages: 2

SP200 - QUICKSTART GUIDE 1

Brand: Jabra Pages: 2

JABRA FREEWAY HFS100

Brand: Jabra Pages: 40

BT150 - Headset - Over-the-ear

Brand: Jabra Pages: 2

Brand: Kampmann Pages: 32

Brand: Keis Pages: 2

Brand: Darimo Pages: 2

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Pages: 2

Brand: Wahoo Pages: 2

PRIME DESIGN VRI3-E-PM11

Brand: Safe Fleet Pages: 12

Brand: Fisher-Price Pages: 8

Brand: Whispbar Pages: 15

Brand: DEFA Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands