Emerson Rosemount 2051 Reference Manual Download Page 75 | Manualshive

Page: 75 / 228

background image

Reference Manual

00809-0100-4107, Rev BA

Section 5: Operation and Maintenance

April 2013

65

Operation and Maintenance

Section 5

Operation and Maintenance

Overview   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 65
Safety messages  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 65
Calibration overview  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 66
Trim the pressure signal  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 71
Perform a Sensor Trim  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 72
Switching HART Revision   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 78

5.1

Overview

This section contains information on calibrating Rosemount 2051 Pressure Transmitters.

Field Communicator, AMS, Device Manager and Local Operator Interface (LOI) instructions are
given to perform configuration functions.

5.2

Safety messages

Procedures and instructions in this section may require special precautions to ensure the safety
of the personnel performing the operations. Information that raises potential safety issues is

indicated by a warning symbol (

). Refer to the following safety messages before performing

an operation preceded by this symbol.

5.2.1

Warnings

Explosions could result in death or serious injury:
Installation of this transmitter in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Please review
the approvals section of the Rosemount 2051 reference manual for any restrictions
associated with a safe installation.



Before connecting a Field Communicator in an explosive atmosphere, ensure the
instruments in the loop are installed in accordance with intrinsically safe or

non-incendive field wiring practices.



In an Explosion-Proof/Flameproof installation, do not remove the transmitter covers

when power is applied to the unit.

Process leaks may cause harm or result in death.



Install and tighten process connectors before applying pressure.

Electrical shock can result in death or serious injury.



Avoid contact with the leads and terminals. High voltage that may be present on leads
can cause electrical shock.

«
...
73
74
75
76
77
...
»

Summary of Contents for Rosemount 2051





































































































































































































































Reviews:

No comments

Related manuals for Rosemount 2051

Brand: Oakton Pages: 16

Brand: OHAUS Pages: 2

Brand: Ralston Instruments Pages: 52

Brand: Flytec Pages: 2

Brand: Topcon Pages: 62

Brand: Shimpo Pages: 68

Brand: HBM Pages: 84

iNELS Air AirCFS-100S

Brand: Elko Pages: 4

Brand: PCE Health and Fitness Pages: 7

SS9007.3 Mini CT Meter

Brand: Saturn South Pages: 18

Brand: Ress Pages: 11

Backsense BS-9000-WD

Brand: Brigade Pages: 42

Brand: Cargo Data Pages: 3

Brand: GeoMax Pages: 14

Brand: SDT Pages: 2

Brand: McIntosh Pages: 17

Recordall Disc Series

Brand: Badger Meter Pages: 4

Brand: LaserLiner Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands