Emerson Rosemount 2051 Reference Manual Download Page 88 | Manualshive

Page: 88 / 228

background image

78

Reference Manual

00809-0100-4107, Rev BA

Section 5: Operation and Maintenance

April 2013

Operation and Maintenance

5.7

Switching HART Revision

Some systems are not capable of communicating with HART Revision 7 devices. The following
procedures list how to change HART revisions between HART Revision 7 and HART Revision 5.

5.7.1

Switching HART revision with Generic Menu

If the HART configuration tool is not capable of communicating with a HART Revision 7 device, it
should load a Generic Menu with limited capability. The following procedures allow for
switching between HART Revision 7 and HART Revision 5 from a Generic Menu.

1.

Locate "Message" field

a.

To change to HART Revision 5, Enter:

HART5

in the message field

b. To change to HART Revision 7, Enter:

HART7

in the message field

5.7.2

Switching HART Revision with Field Communicator

From the HOME screen, enter the fast key sequence and follow steps within the Field
Communicator to complete the HART revision change.

5.7.3

Switching HART Revision with AMS Device Manager

1.

Click on

Manual Setup

and select

HART

2.

Select

Change HART Revision

then follow the on screen prompts.

Note

AMS Device Manager versions 10.5 or greater are compatible with HART Revision 7.

5.7.4

Switching HART revision with Local Operator Interface

Navigate to

HART REV

within the extended menu and select if either

HART REV 5

or

HART REV 7

.

Use

below to change HART Revision.

From the

HOME

screen, enter the fast key sequence

HART5

HART7

Device Dashboard Fast Keys

2, 2, 5, 2, 4

2, 2, 5, 2, 3

«
...
86
87
88
89
90
...
»

Summary of Contents for Rosemount 2051





































































































































































































































Reviews:

No comments

Related manuals for Rosemount 2051

DigitalFlow XMT868i

Brand: Panametrics Pages: 74

Brand: jenway Pages: 18

TEC SourceMeter 2510

Brand: Keithley Pages: 244

Brand: Kawai Pages: 112

Solicap M FTI55

Brand: Endress+Hauser Pages: 92

BUCKMASTERS 1500

Brand: Sig Sauer Pages: 2

Brand: Teledyne Lecroy Pages: 4

Brand: MICRO-EPSILON Pages: 82

Brand: BD Sensors Pages: 4

Brand: Roland Pages: 2

Brand: Karman Pages: 2

Brand: Kinesys Pages: 10

Brand: REED Pages: 20

Brand: Oberheim Pages: 41

Brand: Newton Pages: 112

Brand: THORLABS Pages: 20

Brand: Keithley Pages: 350

Everywhereyoulook Frontline X500

Brand: Teledyne Lecroy Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands