Emerson LURAY ECO CF860BQ00 Owner'S Manual Download Page 29

Page: 29 / 34

emersonfans.com

Please contact 1-800-654-3545 for further assistance

ETL Model No.: CF860

15. Troubleshooting

TROUBLE

PROBABLE CAUSE

SUGGESTED REMEDY

1. Fan will not start.

1. Loose electrical connections in the

1. Check the electrical connections at the ceiling cover.

ceiling cover.

2. Fan sounds noisy.

1. Blades not attached to fan.

1. Attach blades to fan before operating.

2. Wire connectors inside switch housing

2. Check to make sure wire connectors in switch

assembly are rattling.

housing assembly are not rattling against each other or
against the interior wall of the switch housing assembly.

3. Screws holding blades to motor are

3. Tighten screws securely.

loose.

3. Fan wobbles

1. Setscrews in motor coupler are loose.

1. Tighten both setscrews securely in the motor coupler.

excessively.

2. Setscrew in hanger ball/downrod

2. Tighten the setscrew in the hanger ball/downrod

assembly is loose.

assembly.

3. Screws securing fan blades to

3. Check to be sure screws which attach the fan blades

motor are loose.

to the motor are tight.

4. Hanger bracket and/or ceiling outlet

4. Tighten the hanger bracket screws to the outlet box,

box is not securely fastened.

and/or secure outlet box.

FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE
TROUBLESHOOTING YOUR FAN.

WARNING

Make sure main power is turned OFF.

WARNING

Make sure main power is turned OFF.

WARNING

BP7515 CF860 Luray Eco 1/4/16 2:35 PM Page 29

Summary of Contents for LURAY ECO CF860BQ00



































Search results

Summary of Contents for LURAY ECO CF860BQ00

Reviews:

Related manuals for LURAY ECO CF860BQ00

Brands by name

Popular brands

Emerson LURAY ECO CF860BQ00, Owner'S Manual

Search results

Summary of Contents for LURAY ECO CF860BQ00

Reviews:

Related manuals for LURAY ECO CF860BQ00

Brands by name

Popular brands