Emerson Liebert Challenger 3000 Installation Manual Download | Manualshive

Page: 72 / 88

background image

Split System Models

66

Figure 35 Detail of ceiling hanging bracket

7.5.2 Ducting

The total external static pressure for the inlet and outlet ducts, including grille, must not exceed

0.5 inches of H

2

O. Hood intake dimensions should be the same as the condensing unit duct dimen-

sions.
If the condensing unit is located close to the outside of the building, rain hoods must be installed. In

addition, install a triple layer bird screen over rain hood openings to eliminate the possibility of

insects, birds, water, or debris entering the unit.
Use flexible ductwork or nonflammable cloth collars to attach ductwork to the unit and to control

vibration transmission to the building. Attach the ductwork to the unit using the flanges provided.

Locate the unit and ductwork so that the return air does not short circuit to the supply air inlet.
Avoid directing the hot exhaust air toward adjacent doors or windows.
Normal operating sound may be objectionable if the condensing unit is placed directly over quiet work

areas. Ductwork that runs through a conditioned space or is exposed to areas where condensation

may occur must be insulated. Whenever possible, ductwork should be suspended using flexible hang-

ers. Ductwork should not be fastened directly to the building structure. In applications where the ceil-

ing plenum is used as the heat rejection domain, the discharge air must be directed away from the

condensing unit air inlet and a screen must be added to the end of the discharge duct to protect ser-

vice personnel.
For multiple unit installations, space the units so that the hot condensing unit exhaust air is not

directed toward the air inlet of an adjacent unit.

Table 31

Airflow CFM (CMH)

3-Ton

5-Ton

60 Hz

2000 (3398)

3500 (5947)

50 Hz

1650 (2800)

3500 (5947)

3/8" threaded rod

(field-supplied)

3/8" hex nut
3/8" washer

Sleeve

Isolator

3/8" fender washer

3/8" hex nut

3/8" hex nut

Nylock

Unit base pan (ref)

«
...
70
71
72
73
74
...
»

Summary of Contents for Liebert Challenger 3000

























































































Reviews:

No comments

Related manuals for Liebert Challenger 3000

Brand: Daitsu Pages: 21

Brand: Daitsu Pages: 21

Brand: Daitsu Pages: 21

Brand: Daitsu Pages: 21

Brand: Daikin Pages: 19

Brand: Gree Pages: 86

Intense Pure Air XL Connect PU6080

Brand: Rowenta Pages: 76

Brand: Eco-De Pages: 47

NovEcos Split 11

Brand: Olimpia splendid Pages: 28

Brand: A.O. Smith Pages: 16

Brand: Carrier Pages: 10

Brand: Daikin Pages: 22

Brand: Tadiran Telecom Pages: 4

Brand: York Pages: 32

Brand: Gree Pages: 24

Brand: Unical Air Pages: 24

Brand: Omega Altise Pages: 24

Brand: Heat Controller Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands