12
EN
P
REPARATION
Initial Setup
This section will guide you through the unit’s initial setting which includes
selecting a language for your on-screen menu and auto channel scan,
which automatically scans and memorizes viewable channels.
Before you begin:
Make sure if the unit is connected to antenna or cables.
1
After making all the necessary connections, press
[POWER]
to turn on the unit.
This operation may take a few moments.
2
Use
[Cursor
K
/
L
]
to select the on-screen language
from the choices on the right side of the TV screen.
(English / Español / Français)
Initial Setup
Initial Setup
Select the language for setup display.
Elija el idioma de ajuste.
Sélectionner langue écran config.
Select
Enter
Skip
SETUP
Español
Français
ENTER
English
“Initial Setup” menu on step 3 will be displayed in the
selected language after you press
[ENTER]
.
3
Use
[Cursor
K
/
L
]
to select “Air” for TV channels or
“Cable” for CATV channels, then press
[ENTER]
.
Initial Setup
Initial Setup
Air
Cable
Select
Enter
Skip
SETUP
Back
BACK
ENTER
Make sure the antenna is connected to "ANT.IN" jack.
Select the destination of "ANT.IN" jack.
Air
Cable
ANT.IN
Or
Scanning and memorizing of channels start
automatically.
Initial Setup
Initial Setup
Now the system is scanning for channels,please wait.
Skip
SETUP
5%
Analog channels
1ch
Digital channels
0ch
5
•
•
•
4
Use
[Cursor
s
/
B
]
to select the desired mode for
energy saving, then press
[ENTER]
.
Exit
SETUP
Initial Setup
Initial Setup
Select
Enter
ENTER
Home
Retail
Select “Retail” or “Home” for your location.
Select “Retail” if you want backlight to be brighter.
Select “Home” to reduce the power consumption.
When the initial setup is completed, the lowest
memorized channel with the confirmation message
of the energy saving mode will be displayed on the
TV screen.
Note:
• If you connect the cable system directly, contact the CATV
installer.
• If you press
[POWER]
or
[SETUP]
during auto channel
scan, this setting will be canceled.
• The initial auto channel scan function can be executed
for either “Air” or “Cable” only once. When you change the
connection (Air/Cable), set auto channel scan again.
(Refer to page 17.)
• If there is no signal input from the antenna terminal and
no operation for several seconds after you turn on the unit,
“Helpful Hints” appears. Follow the instructions listed on
the TV screen.
No channel is registered.
Press and hold "ENTER" key on the remote control for 3 seconds.
Contact support hotline provided on manual or back of unit.
Sin canal registrado.
Pulse durante 3 segundos la tecla "ENTER" en el control remoto.
Llame teléfono de apoyo en manual o atrás de TV.
Pas de chaîne consign.
Enfoncez "ENTER" 3 secondes sur la télécommande.
Contacter numero d'urgence dans manuel ou arrière appareil.
2-2
• When you select “Home”, brightness of backlight darkens
compared to “Retail”. This is not a malfunction.
After an initial setup is completed...
If you want to scan the channels automatically again,
refer to “Auto Channel Scan” on page 17.
You can add the desired channels unmemorized by
“Autoscan”. Refer to “Manual Register” on page 19.
If you want to change the other language from the
one you chose, refer to “Language Selection” on
page 20.
If you want to change the mode for energy saving,
refer to “Energy Saving Mode” on page 30.
•
•
•
•
•
•
•
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
