Emerson Keystone EPI2 Installation, Operation And Maintenance Manual Download Page 29 | Manualshive

Page: 29 / 36

background image

Installation, Operation and Maintenance Manual

VCIOM-02377-EN Rev. 0

May 2022

25

Section 9: Local Settings

Local Settings

Section 9: Local Settings

The DeviceNet interface module is equipped with 3 on-board selector switches to allow the

operator configuration of both the MACID and the Baud Rate of DeviceNet communication.

To access the on-board interface on the DeviceNet interface module, it is necessary to
follow the procedures explained in Installation, Operation and Maintenance Manual for

Keystone EPI2, Electric Actuator, Section 6, Actuator Settings and Configuration, and then

follow the procedures described in the next sections.

9.1

On-Board Interface

The on-board interface is equipped with the following switches and indications.

Figure 23

MSB-LSB Address

BCD Rotary switches

DATA_RATE

BCD Rotary switch

CNF_OK LED

ENTER pushbutton

ENA_CFG switch

ON_CFG LED

«
...
27
28
29
30
31
...
»

Summary of Contents for Keystone EPI2





































Reviews:

No comments

Related manuals for Keystone EPI2

Brand: ECKELMANN Pages: 178

Brand: UCS Pages: 4

Brand: Saga Pages: 9

Brand: Samson Pages: 73

Brand: H3C Pages: 5

Brand: H3C Pages: 4

Brand: Jandy Pages: 28

Brand: Jands Pages: 6

Brand: Dakota Digital Pages: 12

Brand: oventrop Pages: 64

Brand: K&K Pages: 10

MorphoAccess VP MD

Brand: Idemia Pages: 29

Brand: QUICK DAM Pages: 16

SR-ZG9001T-RGBW

Brand: Sunricher Pages: 3

Brand: LOGICDATA Pages: 23

TITAN-TRACKSIDE-3

Brand: Remote Control Systems Pages: 4

Brand: Planar Pages: 162

Brand: THK Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands