background image

630 Series

3

Table 2.

 Type 630 Regulator Outlet Pressure Ranges and Maximum Outlet Pressures

REgUlaTOR

COnSTRUCTIOn

OUTlET PRESSURE RangE

SPRIng PaRT 

nUMBER

MaXIMUM OPERaTIng 

OUTlET PRESSURE

MaXIMUM OUTlET 

PRESSURE 

OVER SETPOInT

(1)

MaXIMUM EMERgEnCy 

OUTlET (CaSIng) 

PRESSURE

(4)

psig

bar

psig

bar

psig

bar

psig

bar

low-Pressure

3 to 10

0.21 to 0.69 

0W019227022

10

0.69

20

1.38

66

4.55

8 to 20

0.55 to 1.38

0W019127022

20

1.38

17 to 30

1.17 to 2.07

0W019027022

30

2.07

20

(2)

1.38

(2)

27 to 40

1.86 to 2.76

0Y066427022

40

2.76

Limited by Maximum 

Emergency Outlet Pressure

High-Pressure

27 to 50

46 to 95

90 to 150

150 to 200

200 to 275

1.86 to 3.45

3.17 to 6.55

6.21 to 10.3

10.3 to 13.8

13.8 to 19.0

0W019227022

0W019127022

0W019027022

0Y066427022

1J146927142

50

95

150

200

275

3.45

6.55

10.3

13.8

19.0

200

13.8

550

37.9

275 to 500

19.0 to 34.5

1K370927082

500

34.5

200

(3)

1.38

(2)

1. Damage to internal parts of the regulator may occur if outlet pressure exceeds the actual pressure setting by amounts greater than those shown in this column.

2. For outlet pressure settings to 25 psig / 1.72 bar only. For pressure settings over 25 psig / 1.72 bar, outlet pressure is limited by maximum emergency outlet pressure of 45 psig / 3.10 bar.

3. For outlet pressure settings to 350 psig / 24.1 bar only. For pressure settings over 350 psig / 24.1 bar, outlet pressure is limited by maximum emergency outlet pressure of 550 psig / 37.9 bar.

4. Leakage or bursting of pressure-containing parts may occur if outlet pressure exceeds these values.

Table 3.

 Type 630R Relief Pressure Ranges

RElIEf ValVE

COnSTRUCTIOn

RElIEf (InlET) 

PRESSURE RangE

PaRT nUMBER

MaXIMUM allOWaBlE 

RElIEf (InlET) PRESSURE, 

psig / bar

MaXIMUM EMERgEnCy 

InlET (CaSIng) PRESSURE

(1)

psig

bar

psig

bar

low-Pressure

3 to 8

6 to 17

15 to 22

20 to 35

35 to 50

0.21 to 0.55

0.41 to 1.17

1.03 to 1.52

1.38 to 2.41

2.41 to 3.45

0W019227022

0W019127022

0W019027022

0Y066427022

1J146927142

Relief Pressure Setting Plus 

Maximum Allowable Buildup of 

25 psig / 1.72 bar

75

5.17

High-Pressure

30 to 70

50 to 95

75 to 175

150 to 250

2.07 to 4.83

3.45 to 6.55

5.17 to 12.1

10.3 to 17.2

0W019127022

0W019027022

0Y066427022

1J146927142

Relief Pressure Setting Plus 

Maximum Allowable Buildup of 

250 psig / 17.2 bar

550

37.9

1. Leakage or bursting of pressure-containing parts may occur if inlet pressure exceeds these values.

To avoid overpressure, provide an 

appropriate overpressure protection 

device to ensure that none of the limits 

listed in Specifications section, Tables 1 

through 3 will be exceeded.

Regulator or relief valve operation below the limits 

specified in Specifications section, Tables 1 through 3 

does not preclude the possibility of damage from external 

sources or from debris in the gas line. Inspect the 

regulator for damage after any overpressure condition.

Startup

Starting up the unit consists of opening the upstream 

block valve, introducing gas pressure. Use gauges to 

monitor pressures during startup.
The range of allowable pressure settings is marked 

on the nameplate. If a pressure setting beyond the 

nameplate range is required, substitute an appropriate 

spring selected from Table 5. Be sure to change the 

nameplate to indicate the new pressure range.

Table 1. 

Maximum Allowable Inlet Pressures and Pressure Drops

ORIfICE SIzE

MaXIMUM allOWaBlE 

InlET PRESSURE

(1)

MaXIMUM allOWaBlE PRESSURE DROP

nylon (Pa)

(2)

 and

Polytetrafluoroethylene 

(PTfE) Disk

fluorocarbon (fKM) Disk

nitrile (nBR)

(2)

 Disk

In.

mm

psig

bar

psig

bar

psig

bar

psig

bar

1/8 and 3/16 

3.2 and 4.8

1500

103

1500

103

200

13.8

600

 41.4

1/4

6.4

1000

69

3/8

9.5

1000

69

500

34.5

500

34.5

1/2

13

750

51.7

250

17.2

250

17.2

Note: Maximum inlet pressure not exceeded 1500 psig / 103 bar.

1.  Inlet pressure must not exceed the sum of the actual outlet pressure setting and the maximum allowable pressure drop. For example, with an outlet pressure setting of 200 psig / 13.8 bar 

and a 3/8 in. / 9.5 mm orifice with a maximum allowable pressure drop of 500 psid / 34.5 bar d, the maximum inlet pressure is 700 psig / 48.3 bar.

2.  Nitrile (NBR) valve disks are normally furnished for pressure drops to 200 psi / 13.8 bar, differential. For better erosion resistance, Nylon (PA) valve disks are normally furnished for 

higher 

pressure drops. Some erosion of valve disks occurs at all pressure drops due to solid particles in the flow stream. The rate of erosion is higher with large amounts of impurities in the 

flow stream and with high pressure drops. Valve disks and other regulator parts must be inspected periodically for erosion and damage and must be replaced as necessary. 

Summary of Contents for Fisher 630 Series













Reviews: