manualshive.com logo in svg

Emerson Easyheat GC-1, Service Manual

Share
Download
Emerson Easyheat GC-1 Service Manual Download Page 14

Grinder Replacement

Removing Grinder

DANGER

  SHOCK HAZARD!
  Turn off electrical 

power at circuit breaker, use voltmeter 

or circuit tester to ensure that 
POWER IS OFF.

1.  Turn off electrical supply and water 

supply to grinder.

2.  Disconnect cold water connection from 

grinder body.

3.  Disconnect waste line from grinder.

4.  Remove terminal box.

5.  Remove trim band.

6.  Mark to identify all motor leads wires 

and electrical supply wires, then discon-
nect wires, grounding wire and conduit 
from grinder. 

7.  Remove the 6 mounting screws used to 

secure the grinder to the table.

8.  Loosen the two lower jam nuts used to 

secure leg position.

9.  Use channel lock or similar to lower 

grinder from mounting gasket.

10.  Once free, slide grinder off table.

step 

2

step 

4

step 

6

step 

3

step 

5

step 

7

step 

9

step 

10

step 

8

grind2energy.com

 

Grind2Energy Technical Support: 844-874-7529     |     12

  

G2E015-15F-89-84

Summary of Contents for Easyheat GC-1























Reviews:

No comments

Brands by name

Popular brands

Load more brands