Emerson Daniel 788DVC User Manual Download Page 91

Page: 91 / 94

Needle valve

A.1

Disassembly and assembly

Figure A-1: Needle valve

Procedure

1. Isolate and remove all pressure and drain before maintenance.
2. All parts associated with the adjustment stem are removable when the retainer is

removed. Remove the adjustment stem by turning it counterclockwise.

3. For pilots used on crude oil, gasoline, diesel fuel or other general liquid hydrocarbon

service, apply a light oil or general purpose grease to all O-rings to prevent cutting
and to facilitate assembly. Use a light oil only for Butane and Propane service.
Tools required:

•

Retaining ring pliers

•

Ratchet wrench

•

Pin removal tool

•

Needle nose pliers

User manual

Needle valve

P/N 3-9008-556

October 2019

User manual

Summary of Contents for Daniel 788DVC































































































Search results

Summary of Contents for Daniel 788DVC

Reviews:

Related manuals for Daniel 788DVC

Brands by name

Popular brands

Emerson Daniel 788DVC, User Manual

Search results

Summary of Contents for Daniel 788DVC

Reviews:

Related manuals for Daniel 788DVC

Brands by name

Popular brands