background image

Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 9). If you feel
you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.

WARNING

!

This Manual Is Designed to Make it as Easy as Possible for You to Assemble,

Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips head screwdriver

One stepladder

One wire stripper

Materials

Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would be
a 3-conductor (2-wire with ground) of following size:

Installed Wire Length

Wire Size A.W.G.

Up to 50 ft.

14

50-100 ft.

12

Your Emerson ceiling fan comes supplied with a
Fan/Light Remote Control which consists of a receiver
mounted inside the ceiling cover of the fan motor
housing. This system allows you to regulate your ceiling
fan speed and light ON/OFF.

4

U.L. Model No.:  CF4801 and CF4501

2. Electrical Requirements

Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.

To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable for
Fan Support of  22.7 kg. (50 lbs.) or less”, and use
screws supplied with outlet box. Most outlet boxes
commonly used for support of light fixtures are not
acceptable for fan support and may need to be
replaced. Consult a qualified electrician if in doubt.

WARNING

!

Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned
off at the main fuse box before wiring. All wiring must
be in accordance with National and Local codes and
the ceiling fan must be properly grounded as a
precaution against possible electrical shock.

WARNING

!

To avoid fire or shock, follow all wiring instructions
carefully.

Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.

WARNING

!

If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.

1. Unpacking Instructions

(Continued)

Summary of Contents for CROWN SELECT CF4501AP00





















Reviews: