background image

2

Safety Instructions

TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK,
OR INJURY TO PERSONS, OBSERVE THE
FOLLOWING:
a. Use this unit only in a manner intended by the

manufacturer.  If you have questions, contact the
manufacturer.

b. Before servicing or cleaning unit, switch power off

at service panel and lock service panel
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a warning device, such as a tag, to the
service panel.

WARNING

!

Additional Safety Instructions for Installation

1. To avoid possible shock, be sure electricity is turned

off at the fuse box before wiring, and do not operate
fan without blades.

2. All wiring must be in accordance with the National

Electrical Code “ANSI/NFPA 70-2014” and Local
Electrical Codes. Use the National Electrical Code if
Local Codes do not exist. The ceiling fan must be
grounded as a precaution against possible electrical
shock. Electrical installation should be made or
approved by a licensed electrician.

3. The outlet box and joist must be securely mounted

and capable of reliably supporting at least 50 pounds.
Use only U.L. outlet boxes listed as “Acceptable for
Fan Support of 22.7 kg. (50 lbs.) or less”, and use the
mounting screws provided with the outlet box. Most
outlet boxes commonly used for support of light
fixtures are not acceptable for fan support and may
need to be replaced. Consult a qualified electrician if
in doubt.

4. The downrod furnished with the fan provides the

minimum recommended floor to fan blade clearance
for an 8 foot ceiling.

5. The fan must be mounted with the fan blades at least

7 feet from the floor to prevent accidental contact with
the fan blades.

6. Follow the recommended instructions for the proper

method of wiring your ceiling fan. If you do not know
enough about electrical wiring, have your fan installed
by a licensed electrician.

WARNING: 

To reduce the risk of electrical shock, this

fan must be installed with an isolating wall
control/switch.

NOTE:

This fan is suitable for use with solid-state speed

controls.

WARNING:

To avoid fire, shock or injury, do not use an

Emerson or any other brand of control not specifically
approved for this fan.

WARNING:

This product is designed to use only those

parts supplied with this product and/or any accessories
designated specifically for use this product by Emerson
Electric Co. Substitution of parts or accessories not
designated for use with this product by Emerson could
result in personal injury or property damage.

WARNING: 

To reduce the risk of personal injury, do not

bend the blade flange when installing the blade flanges,
balancing the blades or cleaning the fan. Do not insert
foreign objects in between rotating fan blades.

NOTE:

All setscrews must be checked and re-tightened

where necessary before installation.

1. Read your owner’s manual carefully and keep it for

future reference.

2. Be careful of the fan and blades when cleaning,

painting, or working near the fan. Always turn off the
power to the ceiling fan before servicing.

3. Do not put anything into the fan blades while they are

turning.

4. Do not operate reversing switch until fan blades have

come to a complete stop.

DATE CODE:

The date code of this fan may be found on the box, stamped in ink on a white label. You should record

this data above and keep it in a safe place for future use.

U.L. Model No.:  CF4801 and CF4501

READ AND SAVE THESE INSTRUCTIONS

Table of Contents

Section

Page

Safety Instructions   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1. Unpacking Instructions   . . . . . . . . . . . . . . . . . . . . . . . . .3-4
2. Electrical Requirements    . . . . . . . . . . . . . . . . . . . . . . . . . .4
3. Ceiling Fan Assembly    . . . . . . . . . . . . . . . . . . . . . . . . . .5-7
4. How to Hang Your Ceiling Fan    . . . . . . . . . . . . . . . . . . . .8
5. How to Wire Your Ceiling Fan  . . . . . . . . . . . . . . . . . . . . . .9
6. Final Assembly   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
7. Using Your Ceiling Fan   . . . . . . . . . . . . . . . . . . . . . . . . . .10

Section

Page

8. Attaching Optional Light Kit   . . . . . . . . . . . . . . . . . . . . . . .11
9.   Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
10. Accessories  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
11. Repair Parts   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
12. Crown Select Repair Parts   . . . . . . . . . . . . . . . . . . . . . .13
13. Premium Select Repair Parts   . . . . . . . . . . . . . . . . .14-15
14. Trouble Shooting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Ceiling Fan Limited Warranty   . . . . . . . . . . . . . . . . . . . . . . .19

Summary of Contents for CROWN SELECT CF4501AP00





















Reviews: