manualshive.com logo in svg

Emerson ACC/ARTM-7221/FC, Installation Manual

Share
Download
Emerson ACC/ARTM-7221/FC Installation Manual Download Page 19

Sicherheitshinweise

ACC/ARTM-7221/FC Installation Guide (6806800E98A)

19

   

RJ-45 Stecker

 

Beschädigung des RTMs und des Telefons
RJ-45 Stecker an der Frontblende
Die RJ-45 Stecker an der Frontblende werden für verschiedene Schnittstellen 
verwendet, die nicht verwechselt werden dürfen. Wenn Sie ein Telefon oder ein E1/T1 
Netzwerk an eines der mit COM gekennzeichneten seriellen Stecker anschließen oder 
wenn Sie ein serielles Gerät an die mit E1/T1 gekennzeichneten Stecker anschließen, 
kann das Telefon oder das RTM beschädigt werden.
Schließen Sie deshalb nur E1/T1 Netze an die mit E1/T1 gekennzeichneten Stecker an 
und schließen Sie nur serielle Geräte an die mit COM gekennzeichneten Stecker an.

Umweltschutz

Entsorgen Sie alte RTMs stets gemäß der in Ihrem Land gültigen Gesetzgebung, wenn 
möglich immer umweltfreundlich.

Laser

Einige Varianten des Produktes sind Laserprodukte der Klasse I. Um nicht schädlicher 
Laserstrahlung ausgesetzt zu werden, beachten Sie die folgenden Hinweise: 
Anpassungen am Produkt, die Bedienung von Steuerelementen sowie die Durchführung 
von Prozeduren dürfen nur gemäß den Anweisungen in diesem Dokument erfolgen.

Summary of Contents for ACC/ARTM-7221/FC























































Reviews:

No comments

Brands by name

Popular brands

Load more brands