Emerson ACC/ARTM-7221/FC Page 17 Installation Manual Download | Manualshive

Page: 17 / 54

background image

ACC/ARTM-7221/FC Installation Guide (6806800E98A)

17

Sicherheitshinweise

Dieser Abschnitt enthält Sicherheitshinweise, die bei Installation, Betrieb und Wartung
des Produkts zu beachten sind.

Wir sind darauf bedacht, alle notwendigen Informationen, die für die Installation und den
Betrieb erforderlich sind, in diesem Handbuch bereit zu stellen. Da es sich jedoch um
ein komplexes Produkt mit vielfältigen Einsatzmöglichkeiten handelt, können wir die
Vollständigkeit der im Handbuch enthaltenen Informationen nicht garantieren. Falls Sie
weitere Informationen benötigen sollten, wenden Sie sich bitte an die für Sie zuständige
Geschäftsstelle von Emerson.

Das Produkt erfüllt die für die Industrie geforderten Sicherheitsvorschriften und darf
ausschließlich für Anwendungen in der Telekommunikationsindustrie und im
Zusammenhang mit Industriesteuerungen verwendet werden.

Installation, Wartung und Betrieb dürfen nur von durch Emerson ausgebildetem oder im
Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgeführt werden.
Die in diesem Handbuch enthaltenen Informationen dienen ausschließlich dazu, das
Wissen von Fachpersonal zu ergänzen, können es aber in keinem Fall ersetzen.

EMV

Das RTM wurde in einem Emerson-Standardsystem getestet. Es erfüllt die für digitale
Geräte der Klasse A gültigen Grenzwerte in einem solchen System gemäß den FCC-
Richtlinien Abschnitt 15 bzw. EN 55022 Klasse A. Diese Grenzwerte sollen einen
angemessenen Schutz vor Störstrahlung beim Betrieb des RTMs in Gewerbe- sowie
Industriegebieten gewährleisten.

Das RTM arbeitet im Hochfrequenzbereich und erzeugt Störstrahlung. Bei
unsachgemäßem Einbau und anderem als in diesem Handbuch beschriebenen Betrieb
können Störungen im Hochfrequenzbereich auftreten.

Warnung! Dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im
Wohnbereich Funkstörungen verursachen. In diesem Fall kann vom Betreiber verlangt
werden, angemessene Maßnahmen durchzuführen.

«
...
15
16
17
18
19
...
»

Summary of Contents for ACC/ARTM-7221/FC























































Reviews:

No comments

Related manuals for ACC/ARTM-7221/FC

Brand: ABB Pages: 27

Brand: Omnia Pages: 8

D-MAS HyperSat 2540

Brand: DanMedical Pages: 103

Brand: Paia Pages: 11

Brand: CAB Pages: 39

Brand: CAB Pages: 27

Sportsound SSR-200

Brand: Daktronics Pages: 5

Brand: Farmi Forest Corporation Pages: 32

Brand: Unitary products group Pages: 28

Brand: Gardner Bender Pages: 8

Brand: NARIKA Pages: 2

Brand: Macht Dental Pages: 8

Brand: MagCore Pages: 80

Brand: MagCore Pages: 80

Brand: OAKWORKS Pages: 2

Brand: Oakton Pages: 2

Brand: Oakton Pages: 2

Brand: O2matic Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands