background image

3

Preparation before Use

The air conditioner has an  Auto-Restart function.  

    

Each time after the remote control is replaced with new batteries or is energized, 

 auto presetting

heat  pump.If the air conditioner you purchased is a Cooling Only one, heat pump remote controller can also be 

used.

 remote control

Remote Control Presetting

Before using the air conditioner, be sure to check and preset the following.

Auto Restart Presetting

Hold down any button on remote control to activate the back light. It automatically shuts off 10 seconds 

later.

Note: Back-light is an optional function.

Back-light Function 

(optional)

of Remote Control

This appliance is made of recyclable or re-usable material. Scrapping must be carried out  in 

compliance with local waste disposal regulations. Before scrapping it, make sure to cut off the

 mains cord so that the appliance cannot be re-used. 

For more detailed information on handling and recycling this product, contact your local authorities

who deal with the separate collection of rubbish or the shop where you bought the appliance. 

SCRAPPING OF APPLIANCE 

This marking indicates that this product should not be disposed 

with other household wastes throughout the North America. To

 prevent possible harm to the environment or human health from 

uncontrolled waste disposal, recycle it responsibly to promote 

the sustainable reuse of material resources. To return your 

used device, please use the return and collection systems or

contact the retailer where the product was purchased. 

They can take this product for environmental safe recycling.

Note

Preset

Safeguarding the environment

When charging refrigerant into the system, make sure to charge in liquid state, if 

the refrigerant of the appliance is R410A.Otherwise, chemical  composition of  

refrigerant (R410A) inside the system may change and thus affect performance 

of the air conditioner. 

According to the character of 

pressure of the tube is very high, so be sure to be careful when you install and 

repair the appliance.  

refrigerant (R410A,the value of GWP is 2088), the

If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.
The air conditioner must be installed by trained, qualified installers 

and service mechanics.

The temperature of refrigerant circuit will be high, please keep the 

interconnection cable away from the copper tube.

Summary of Contents for 12K













































































































Reviews: