EMC2 VNX VG2 Hardware Information Manual Download

Page: 38 / 43

Component description

EMC VNX VG2/VG8 Hardware Information Guide

Two-port 10-Gb/s FCoE I/O module LEDs

The two-port 10-Gb/s FCoE I/O module has three types of status LEDs.

Figure 32

shows

the LEDs and

Table 17

describes them.

Figure 32 Two-port 10-GbE FCoE I/O module LEDs

Two-port 10-Gb/s optical I/O module

The two-port 10-Gb/s optical or active Twinax I/O module (labeled 10 GbE v3 on the latch
handle) comes with two optical ports, one power/fault LED, and a link and activity LED for
each port (

Figure 33 on page 38

). The optical ports on this I/O module can interface at

speeds of 10 Gb/s. The two-port 10-Gb/s optical I/O module uses the SFP+ transceiver
module (see the section describing the SFP and SFP+

“Four-port 8-Gb/s FC I/O module” on

page 27

for more information about the SFP and SFP+ modules). The two-port 10-Gb/s

optical I/O module uses a different SFP+, hence the required SFP+ module uses a different
part number (see the

VNX

VG2/VG8 Parts Location Guide

for more information).

Link LED

Activity LED

CNS-001672

Power/fault LED

Table 17 Two-port 10-Gb/s FCoE I/O module LEDs

LED

Color

State

Description

Power/Fault

Green

I/O module is powered up.

—

Off

I/O module is powered down.

Amber

I/O module has faulted.

Link

Green

Network connection

—

Off

No network connection

Activity

Amber

Blinking

Transmit/receive activity

—

Off

No activity

Summary of Contents for VNX VG2












































Search results

Summary of Contents for VNX VG2

Reviews:

Related manuals for VNX VG2

Brands by name

Popular brands

EMC2 VNX VG2, Hardware Information Manual

Search results

Summary of Contents for VNX VG2

Reviews:

Related manuals for VNX VG2

Brands by name

Popular brands