manualshive.com logo in svg

EMC Avamar Data Store Gen4T, Customer Service Manual, Page: 30 / 32

Share
Download
EMC Avamar Data Store Gen4T Customer Service Manual Download Page 30

Figure 14  Power Supply Installation

2. Insert the replacement power supply into the SP module and push until it clicks into

place.

3. Connect the AC power cord to the replacement power supply and fasten the retaining

clip to secure the cord.

4. Allow several seconds for the node to recognize the power supply and determine

whether it is working properly. The 

AC Good

 and 

DC Good

 LEDs should illuminate

green. The 

Attention

 LED should stay off.

Verifying the replacement power supply

Procedure

1. Type the following command:

avsysreport power-supply

Output similar to the following is displayed:

=== Power supply redundancy

Status           : Ok

Redundancy State : Fully Redundant

=== Power supplies

Power Supply ID   : 0

Status            : Ok

Location          : PSA

Operational State : Inserted, Power Good

Firmware Revision : 4.20.0.1

Serial Number     : FPSAG144900460

Power Supply ID   : 1

Status            : Ok

Replacing a Power Supply

30

EMC Avamar Data Store Gen4T

  

Customer Service Guide

Summary of Contents for Avamar Data Store Gen4T

































Reviews:

No comments