Elvox 41018 Installer'S Manual Download Page 13

Page: 13 / 15

Calling

Talking

Call ended

No answer

Delete

Back

Delete

Back

Concluded

Porter

No Reply

If the system is busy, with another call, the wait signal is returned:

Busy

If the user is busy or has set the user absent service, these warnings are issued:

Busy

Absent

5.5. Entry control

When there is a keypad on the panel, the display shows the feedback of the operation of the entry control mode.

This mode lets you activate a previously configured command (e.g. lock, relay, etc.).
For its operation, please refer to the instructions of the keypad module, summarized here.

5.5.1. Operation

The keypad has 2 function keys referred to here as

and

Press the

button and the display to go into “Code Entry” mode.

Each time a digit button is pressed, the display will show the digit for a short time and then overwrite it with an aster-

isk.
The entered code is confirmed by following the instructions shown on the display or by pressing

again.

Summary of Contents for 41018
















Search results

Summary of Contents for 41018

Reviews:

Related manuals for 41018

Brands by name

Popular brands

Elvox 41018, Installer'S Manual

Search results

Summary of Contents for 41018

Reviews:

Related manuals for 41018

Brands by name

Popular brands