Eltroplan REVCON DC 13-400-1-0 Operating Instructions Manual Download Page 40

Page: 40 / 77

Technical data

Operating instructions DC(S)

ELTROPLAN

REVCON



Elektrotechnische Anlagen GmbH

3.4

Switch on current limiter

As the REVCON



DC(S) has got no inrush current limiter (Pre load circuit), it may

exclu-

sively

used in combination with controllers, which are equipped with an internal pre load

circuit for their DC-bus capacitors. The maximum value of the inrush current must not ex-

ceed the rated values of tables 3.3.2.1 to 3.3.2.2.

Stop!

An operation with other types of pre load circuits is allowed only after release by ELTROPLAN

–REVCON and after a corresponding modification of the units.

3.5

RFI-filter

To observe the EMC-rules in accordance with figure 4.4.1.1.1 a radio frequency interfer-

ences filter class A can be preconceived to the REVCON



unit. Please request a RFI filter

if necessary.

STOP

Summary of Contents for REVCON DC 13-400-1-0














































































Search results

Summary of Contents for REVCON DC 13-400-1-0

Reviews:

Related manuals for REVCON DC 13-400-1-0

Brands by name

Popular brands

Eltroplan REVCON DC 13-400-1-0, Operating Instructions Manual

Search results

Summary of Contents for REVCON DC 13-400-1-0

Reviews:

Related manuals for REVCON DC 13-400-1-0

Brands by name

Popular brands