Eltroplan REVCON DC 13-400-1-0 Operating Instructions Manual Download Page 25

Page: 25 / 77

Safety information

Operating instructions DC(S)

ELTROPLAN

REVCON



Elektrotechnische Anlagen GmbH

Connection of further loads

The connection of further loads (e.g. cabinet ventilation or climatisation)

parallel to the frequency inverter / power feed/feedback unit at a common circuit breaker

like in figure 2.6.5 is not allowed. If it's done nevertheless, in case of tripping of the circuit

breaker the connection to the network (energy sink and synchronising element for the

power feed/feedback unit) misses. The IGBT's now switch the DC-voltage directly to the

other loads. The resulting nearly rectangular "net"-voltage drives a current through the

loads, which level and form depends on their impedance. Is the power consumption of the

loads to small, the DC-voltage and also the output voltage of the power feed/feedback unit

rises during the feed back operation. This increased voltage may damage all connected

components.

60kW

Supplying network

Right

False

REVCON

Figure 2.6.5

Summary of Contents for REVCON DC 13-400-1-0














































































Search results

Summary of Contents for REVCON DC 13-400-1-0

Reviews:

Related manuals for REVCON DC 13-400-1-0

Brands by name

Popular brands

Eltroplan REVCON DC 13-400-1-0, Operating Instructions Manual

Search results

Summary of Contents for REVCON DC 13-400-1-0

Reviews:

Related manuals for REVCON DC 13-400-1-0

Brands by name

Popular brands