background image

  WOP-12ac. Quick guide

5


3  Configuration of WOP-12ac network parameters

For remote management of WOP-12ac, set network parameters of the device according to the settings of the 
network that you intend to use. 
In the 

Manage

 menu, open 

Ethernet

 

Settings

 tab and perform the following:

Management VLAN ID

 – specify the VLAN number that will be used for access point management. VLAN 

10 is used in the given example;

Connection Type

 – select 

Static IP

 to set IP addresses for access points manually. If it is necessary to 

distribute IP addresses and other network parameters to access points via the DHCP protocol, set the 

Connection Type

 field to “DHCP” and this will complete the configuration of the network part;

Static IP Address – s

pecify the IP address of WOP-12ac. In the given example, VLAN 10 address is 

192.168.100.3

.

Subnet Mask

 – 

s

pecify the subnet mask. In the given example, subnet mask is 

255.255.255.0

.

Default Gateway – e

nter the IP address of the default gateway field. In the given example, IP address of 

the default gateway is 

192.168.100.1

.

For the new configuration to take effect and the settings to be stored in the non-volatile memory of the access 

point, click the “Update” button.

After the configuration, WOP-12ac will be available in 10 VLAN via 192.168.100.3 address.

Before making changes to the network settings of the access point, make sure that the host computer 
has access to the network where the access point will be located, based on the configured network 

settings. In case of entering and applying incorrect data while changing the settings, undo them by 
resetting the access point to factory settings. To do this, press and hold "F" button on the front panel of 

the device for 20 seconds until the LED indicator is blinking.

Summary of Contents for WEP-12ac























Reviews: