ELTEX NTU-RG-1421G-Wac Operation Manual Download Page 16

Page: 16 / 53

____________________________________________________________________________________

NTU

Optical Network Terminals

off

Wi-Fi is not active

Phone 0

green

phone is off-hook

flashes

port is not registered or authorization is not completed on
SIP server

flashes slowly

receiving call signal

off

RF port is disabled

red

TV signal is not available

orange

signal level does not correspond to the normal (more than
+2 dBm)

Power

off

The device is disconnected from the power source or
faulty

green

The current device configuration differs from the default
one

orange

The default configuration is set

red

device booting

2.6.3

Indication of LAN Interfaces

Table 10 lists operation modes shown by LAN ports LEDs located on the rear panel of the device.

Table 10 – Light Indication of LAN Interfaces

Operation Modes

Yellow LED

Green LED

Port is in 1000Base-T mode, no data
transfer

solid on

The port is in the 1000Base-T mode,
data transfer

solid on

flashes

Port is in 10/100Base-TX mode, no data
transfer

off

solid on

The port is in the 10/100Base-TX mode,
data transfer

off

flashes

2.7

Reboot/Reset to factory defaults

For device reboot, press the

Reset

button once on the device side panel (“F” button on a rear panel for

NTU-RG-1421GC-Wac). In order to reset the device to factory settings, press the

Reset

button (“F”) and hold it

for 7-10 seconds until the

POWER

LED glows red. Factory settings for IP address are:

LAN

—

192.168.1.1, subnet

mask—255.255.255.0.

Access can be provided from LAN 1, LAN 2, LAN 3 and LAN 4 ports.

2.8

Delivery Package

NTU

standard delivery package includes:

–

NTU

optical network terminal;

–

220V/12V power adapter;

–

operation manual.

Summary of Contents for NTU-RG-1421G-Wac






















































Search results

Summary of Contents for NTU-RG-1421G-Wac

Reviews:

Related manuals for NTU-RG-1421G-Wac

Brands by name

Popular brands

ELTEX NTU-RG-1421G-Wac, Operation Manual

Search results

Summary of Contents for NTU-RG-1421G-Wac

Reviews:

Related manuals for NTU-RG-1421G-Wac

Brands by name

Popular brands