ELTEX MA4000-PX Operation And Maintenance Manual Download Page 98

Page: 98 / 181

User Manual, Part IV

Subscriber access/aggregation node МA4000-РХ

28.4

ONT Configuration Procedure

Figure 35 shows steps of ONT configuration.

Fig. 35—ONT Configuration Procedure

Step 1. Prior to proceed to ONT configuration, add the ONT into an OLT configuration. For an ONT

to be added and configured, it does not need to physically connected to OLT. You can view the list of
unactived ONTs with the help of the

show interface ont unactivated

command:

ma4000# show interface ont 0/0/0 unactivated

Slot 0 GPON-port 0 has no unactivated ONTs

Slot 0 total ONT count: 0

Step 2. To specify ONT settings, go to the corresponding view with the help of the interface ont

command. Specify ONT serial number, password, or their combination.

ma4000# configure terminal
ma4000(config)# interface ont 0/0/0
ma4000(config)(if-ont-0/0/0)# serial ELTX5C00008C
ma4000(config)(if-ont-0/0/0)# password 0000000000

Step 3. Apply the changes by using the

do commit

command.

ma4000(config)(if-ont-0/0/0)# do commit

Step 4. OLT entry configuration has pre-defined ONT profiles which will be automatically assigned

to ONT. View the ONT configuration with the help of the

do show interface ont 0/0/0 configuration

command.

Summary of Contents for MA4000-PX






















































































































































































Search results

Summary of Contents for MA4000-PX

Reviews:

Related manuals for MA4000-PX

Brands by name

Popular brands

ELTEX MA4000-PX, Operation And Maintenance Manual

Search results

Summary of Contents for MA4000-PX

Reviews:

Related manuals for MA4000-PX

Brands by name

Popular brands