manualshive.com logo in svg

ELT GsmAlarm-420, Manual, Page: 8 / 27

Share
Download
ELT GsmAlarm-420 Manual Download Page 8

C O N N E C T O R S   A N D   L E D S  

 

_________________________________________________________________________________   

GsmAlarm-420                                                                                                           Software ver. 1.05 
 

- 6 -

 

3.

 

LED INDICATORS 

 

Lihgt indicators facilitate quick adjustment and troubleshooting of the system during installation. 
 
3.1.

 

SIGNAL:  INDICATOR OF SIGNAL STRENGTH AND GSM MODULE OPERATION 
MODE  

 

Indicator state 

Explanation 

Out. 

GSM module is not in use. No power supply or 
system failure. 

 
Continuously On. 
 

There is no GSM operator network registration. 
Possible causes: SIM card PIN code request is not 
deactivated, antenna not connected or poor network 
connection quality. 

Blinking more frequently than once a 
second. 

GSM module is in use: outgoing call or SMS is 
being sent. 

Blinks 5 times, short break after. 

Very good signal. 

Blinks 4 times, short break after. 

Good signal. 

Blinks 3 times, short break after. 

Satisfactory connection. 

Blinks 2 times, short break after. 

Weak connection. 

Blinks once, short break after. 

Poor connection. 

 
3.2.

 

Z1-Z4: INPUT STATUS INDICATOR 

 

Indicator state 

Explanation 

Out. 

Input is not triggered 

Continuously On. 

Input is triggered 

 
3.3.

 

MODE: SYSTEM OPERATION MODE INDICATOR 

 

Indicator state 

Explanation 

Out. 

No power supply or system failure. 

 
Continuously On. 
 

System  is  operative,  disarmed,  no  zone  sensors  have 
been triggered. 

On with short breaks. 

System  is  operative,  disarmed,  but  one  or  more  zone 
sensors have been triggered. 

Blinking with low frequency (once in  
2-3 sec.). 

System is operating in armed mode. 
 

Blinking more frequently than once a 
second. 

System is in alarm state, siren is active, call or SMS is 
sent. If SMS is sent, indicator blinks a little bit slower 
(about twice a second). 

Blinking very rapidly for 2-3 sec. 
 

SMS  instruction  or  DTMF  command  receipt 
confirmation. 

 
3.4.

 

ALARM: ALARM MODE INDICATOR 

 

Indicator state 

Explanation 

Blinks at a permanent rate. 

System is in alarm state, call is made or SMS sent. 

Blinks twice every 2-3 seconds. 

ALRNR1  number  has  not  been  programmed.  In  order 
GsmAlarm-420 could  make calls, this number need to 
be programmed! 

Summary of Contents for GsmAlarm-420




























Reviews:

No comments