manualshive.com logo in svg

ELT GsmAlarm-420, Manual, Page: 4 / 27

Share
Download
ELT GsmAlarm-420 Manual Download Page 4

G E N E R A L   D E S C R I P T I O N  

 

_________________________________________________________________________________   

GsmAlarm-420                                                                                                           Software ver. 1.05 
 

- 2 -

Remote  control  and  monitoring  device  GsmAlarm-420  has  built-in  radio  transmitter  operating  on 
GSM900 and GSM1800 networks.  
Do not use the device where it can cause interferences and danger.   
Do not arrange the device close to medical equipment and appliances.  
Do not use the device in explosive environment. 
Device is not resistant to moisture, chemical materials or mechanical damage.  
Don’t attempt to personally repair the system. 
System label is on the bottom side of the device. 
 
 

This symbol on the product or on its packaging means that your electrical and electronic 
equipment should be disposed at the end of life separately from your household wastes. 
There are separate collection systems for recycling in EU. For more information, please 
contact the local authority or the dealer where you purchased the product. 

 

 

 

The device compliance to RoHS Directive.                                                                                

 
 
 
1.2.

 

PACKAGE CONTENT 

 
GsmAlarm-420 main board ........................................................................... Qnty   1 
GSM antenna with magnetic fix and 2 m lead cable ...................................... Qnty   1 
Microphone with 1,5 m lead cable ................................................................. Qnty   1 
Load resistors 2,2k

Ω

 ±5% ............................................................................. Qnty   6 

Clamping cable for accumulator connection .................................................. Qnty   1 
User‘s manual ................................................................................................ Qnty   1 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for GsmAlarm-420




























Reviews:

No comments