manualshive.com logo in svg

ELT GsmAlarm-420, Manual, Page: 20 / 27

Share
Download
ELT GsmAlarm-420 Manual Download Page 20

P R O G R A M M I N G  

 

_________________________________________________________________________________   

GsmAlarm-420                                                                                                           Software ver. 1.05 
 

- 18 -

Note!  If several functions have to be operative, sum of the numbers is used. E.g.: for all three Y 
functions to be active, Y value must be 7 (1+2+4=7). 
5.3.2.3.

 

PARAMETER F : SYSTEM RESPONSE TO INCOMING CALLS AND NUMBER 
OF CALLS IN ALARM MODE 

 

System response to incoming call 

E

XY 

Number of the calls in alarm 

mode 

X 

Y 

All functions below are deactivated. 

0 

0 

- 

If a call is received from unknown 
caller, user ALRNR1 will receive a 
SMS with caller‘s number. 
 

1 

1 

After alarm triggering, users 
will be called once. 
 

If calling from user‘s number, after 
3-4 calls the system will pick up, 
armed mode will remain on. 
 

2 

2 

After alarm triggering, users 
will be called twice. 
 

The user ALRNR1 receives an SMS 
message, if GSM connection was 
lost for more than 30 seconds. The 
message is sent only when in armed 
mode. 

4 

4 

If call received not from 
ALRNR1-ALRNR5, thus the 
calling number is in SIM card 
(gate control mode), system 
answers the call after 3-4 
signals, and user can control 
the system with DTMF 
instructions. Call 
automatically cancelled after 
1 minute passes. 

 
Note!  If several functions have to be operative, sum of the numbers is used. 
E.g.: for all three X functions to be active, X value must be 7 (1+2+4=7).  
 
 
5.3.2.4.

 

PARAMETER U : RESERVE BATTETY VOLTAGE 

 
In  the  case  of  use  of  GsmAlarm-420  for  car  protection, it  is  recommended  to  use  not 12V, but  6V 
reserve  battery.  This  will  assure  reliable  charge  of  reserve  battery,  independently  of  the  car  battery 
voltage. 
 
U12: system operates in 12V (premise protection) mode, reserve battery voltage 12V 
U06: system operates in 6V (car protection) mode, reserve battery voltage is 6V.  
 
 
5.4.

 

SMS PASSWORD CHANGE 

 
In  order  to  change  manufacturer-programmed  SMS  password,  send  GsmAlarm420  the  following 
message: 
 
A  A  A  A  A  A A  A    P  A  S  S  W :  A  B  C  D  e  f  g  h 
 
AAAAAAAA  – old SMS password. 
PASSW           – password changing instruction. 
ABCDefgh      – new SMS password. Password must be 8 characters long! 
 
Note!  No characters/spaces can be used before password, space must follow the password. 

Summary of Contents for GsmAlarm-420




























Reviews:

No comments