manualshive.com logo in svg

Elster EK280, Applications Manual, Page: 102 / 163

Share
Download
Elster EK280 Applications Manual Download Page 102

EK280 

Application Manual 

100 

 

7.3.7 

FE260 GSM/GPRS version with ComTSC modem application 

7.3.7.1  General details of the TSC system 

General details of the TSC system, see section 7.1.5.1 on page 57. 

i 

This operating mode only works, if the FE260 includes one of the following 
two GSM/GPRS modem modules. 

 

Integra "M2106+" or "M2106B" with firmware V6.57e and the application 
"ComTSC" (Delivery before April 2014), verifiable by the modem sticker 
illustrated on the right. 
 

 

ECM-GW120 with firmware V7.4

 

7.6 and the application "ComTSC" 

(Delivery before April 2014), verifiable by the modem sticker illustrated on 
the right. 
 

 

i 

If the FE260 includes an ECM-GW120 with the modem sticker illustrated on 
the right, it cannot be parameterized for TSC operation! 
 

 

Initial conditions: 

 

The FE260 is connected and configured as described in chapter 7.3.1. 

 

The SIM card is inserted and unlocked as described in chapter 7.3.2. 

 

7.3.7.2  Parametrization of the EK280 

i 

For parameterization of the EK280 you will require a connection cable for the optical interface as 
well as the enSuite application, which can be downloaded for free at www.elster-instromet.com. 

The procedure is as described in Section 7.3.5.1 on page 89. The parameter file to be used depends on the 
modem type which is fitted to the FE260: 
- Modem type "

ECM-GW120

":  

  

 

EK280_xvx. - FE260 & int. ECM-GW-120 - ComTSC (*)

 

13

   

  

- Modem type "

Integra M2106+" 

or

 "Integra M2106B

": 

  

 

EK280_xvx. - FE260 & int. M2106x - ComTSC (*) 13 

 

7.3.7.3  Parameterization of the GPRS-ComTSC-Modem in the FE260 

Parameterization of the modem application "ComTSC" in the GSM/GPRS modem may be effected either via 
a  GSM-CSD  modem  connection  or  on  location,  via  the  modem  parameterization  interface  on  the  FE260 
modem adapter board. 

 

i 

For the parameterization of the "ComTSC" modem application in an FE260, there is also the 
separate commissioning instruction (ID No. 73021403) [8], which is included with every FE260 
with a ComTSC modem!  

For parameterization of the GPRS-ComTSC modem, please first connect your PC or laptop with the modem 
parameterization  interface  on  the  modem  adapter  board  in  the  FE260,  as  described  in  Section  7.3.5.2 
"Parameterization of the GPRS/TCPserv modems in the FE260", page 91. 
The actual parameterization of the TSC function in the ComTSC modem is then performed pursuant to Section 
7.1.5.3 "Parameterization of the internal ComTSC modem in the EK280", page 58. 

 

7.3.7.4  Checking GSM field strength 

See Chapter 7.1.2.2 "Checking GSM field strength", page 48 

 

7.3.7.5  Retrieving data with enSuite 

See Section 7.1.5.5 

“Retrieving data with enSuite”

Fehler! Verweisquelle konnte nicht gefunden werden.

, 

page 61. 

                                                      
 

13

   The "x" stands for the version of software on the device, e.g. "2v2". 

The star * stands for a small letter which indicates the version of the file, e.g. "a". 

Summary of Contents for EK280




































































































































































Reviews:

No comments