background image

 

iS300/iS300D/iS300Solar

 

SWING

 

GATE

 

OPENER

 

MANUAL

 

1.1 GENERAL PRECAUTION

 

 
WARNING: 

This user manual is only for qualified technicians who are specialized in 
installations and automations. 

1)  All installations, electrical connections, adjustments and testing must be 
 

performed only after reading and understanding of all instructions carefully. 

2)  Before carrying out any installation or maintenance operation, disconnect the 
 

electrical power supply by turning off the mains switch connected upstream 

 

and apply the hazard area notice required by applicable regulations. 

3)  Make sure the existing structure is up to standard in terms of strength and 
 stability. 
4)  When necessary, connect the motorized gate to reliable earth system during 

 electricity 

connection 

phase. 

5) Installation 

requires 

qualified personnel with mechanical and electrical skills. 

6)  Keep the automatic controls (remote, push buttons, key selectors.etc) placed 
 

properly and way from children. 

7)  For replace or repair of motorized system, only original parts must be used. 
 

Any damage caused by inadequate parts and methods will be not claimed to 

 motor 

manufacturer. 

8)  Never operate the drive if you suspect that it might be faulty or will cause 
 

damage to the system. 

9)  The motors are exclusively designed for gate opening and closing application, 
 

any other usage is deem inappropriate. The manufacturer will not be liable for 

 

any damage resulting from the improper use. Improper usage should void all 

 

warranty, and the user accepts sole responsibility for any risks thereby may 

 accrue. 
10)  The system may be operated in proper working order. Always follow the 
 

standard procedures by following the instructions in this installation and 

 operating 

manual. 

11)  Only operate the remote when you have the full view of the gate. 
 

ELSEMA PTY LTD shall not be liable for any injury, damage, or any claim to 
any person or property which may result from improper use or installation 
of this system. 

Please keep this installation manual for future reference. 

 
 
 
 
 
 

1

 

Summary of Contents for iS300













Reviews: