background image

Manual: Data Transfer

Profibus DP,   

EN 50170

 

Multizones Temperature Controller

Series:  R2000, R2100, R2200

Content:

   Series:  R2000, R2100, R2200...................................................................................................................1
1. Disclaimer of liability...................................................................................................................................2
2. Interface, general.......................................................................................................................................2

2.1 Line routing, screening and measures to combat interference voltage................................................3
2.2 Shielding of lines...................................................................................................................................4
2.3  Connection guide ................................................................................................................................5

2.3.1 PROFIBUS - Connections:  ..........................................................................................................5
2.3.2 PROFIBUS - Adjustments:  ...........................................................................................................5
2.3.3 PROFIBUS - Diagnostic displays:..................................................................................................6

3. Data Transfer, general...............................................................................................................................6

3.1 The Communication:............................................................................................................................6
3.2 Process reflection.................................................................................................................................7

3.2.1 From master to slave: ...................................................................................................................7
3.2.2 From slave to master: ...................................................................................................................8
3.2.3 Transmission example...................................................................................................................9

3.3 Configuration channel.........................................................................................................................11

3.3.1 Data transmission, general..........................................................................................................11
3.3.2  Terms..........................................................................................................................................11
3.3.3 Parameter ranges........................................................................................................................11
3.3.4 Configuration of the parameters via the configuration channel...................................................11
3.3.5 Parameter list...............................................................................................................................13
3.3.6 Transmission examples...............................................................................................................15

3.3.6.1 Configuration channel,  Instruction code: 10 H.....................................................................15
3.3.6.2 Configuration channel,  Instruction code: 20 H.....................................................................16
3.3.6.3 Configuration channel,  Instruction code: 21 H.....................................................................17

3.4 Process reflection  and  Configuration channel..................................................................................18

Manual R20-R21-R22-PB-E               Release: 2.04                © Elotech GmbH                         Page 1/20

ELOTECH Industrieelektronik GmbH
Verbindungsstrasse 27
D – 40723 HILDEN
FON +49 2103 / 255 97 0    

FAX  +49 2103 / 255 97 29

www.elotech.de                      

Email: [email protected]

Summary of Contents for R2000





















Reviews: