manualshive.com logo in svg

ELNA eXpressive 970, Service Manual

Share
Download
ELNA eXpressive 970 Service Manual Download Page 64

63

1.  Remove the spool stand, right cover, left cover, base 
  cover and X-carriage cover (see pages 4 – 7).

2.  Attach the Hoop M1 (MB Hoop 240 X 200) to the hoop  
 supporter.  

3.  Open the factory adjusting menu window and press 
 the 

X/Y Motor key to open the X/Y Motor adjusting 

 window.

4.  Press the jog buttons to move the carriage to where 
  the center of the hole in the needle plate is positioned  
  7 mm by 5 mm from the bottom left corner of the inner  
  sides of the hoop. 

5.  Loosen the two setscrews (A) slightly.
  Move the Y-carriage sensor plate slowly to the front 
  until the indication under 

Y changes from “H” to “L”.

  Tighten the two setscrews (A).

6.  Loosen the two setscrews (B) slightly.
  Move the X-carriage sensor plate slowly to the left 
  until the indication under 

X changes from “H” to “L”.

  Tighten the two setscrews (B).

NOTE:
The sensors should not interfere with the carriage.

7.  Attach the parts removed in step 1.

Adjusting the Carriage Home Position

Y-carriage sensor plate

Setscrews (A)

Y-carriage sensor

X-carriage sensor plate

X-carriage sensor

Jog buttons

Setscrews (B)

Front

Front

Back

Left

Right

X

Y

Summary of Contents for eXpressive 970


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands