background image

USER MANUAL

Inteli-Mixer RM-2

10

Operation order

Before turning the machine on carefully examine 
the power adapter, power supply wire and external 
look of the machine. In case of external damage do 
not turn on the machine without permission of the 
specialist.
•  Fixing 

the 

rack. 

    

Put the rack 

1 with the cylinder type end in to 

the back holder 

2 until it is fixed (Fig. 5A, 5B) 

Put the flat side of the rack in to the shaft 

until 

it is fixed and fasten the screw 

4 by the rack fix-

ation wrench (Fig. 5). Find rack fixation wrench 
underneath the machine.

•  To replace the rack perform all the steps in re-

verse order.

View from above

•  Plug  the  adapter  first  to  the  machine  power 

socket then to the power outlet 110-220V 50Hz.

•  Put 

closed tubes in rack adapters.

•  Using 

 buttons select operation program 

(see

 Intelli-mixer program overview table).

•  Set rotation speed and shaking intensity (see 

using mixing programs).   

 

Note ! 

Operation programs can be selected either 

during operation or while mixer is stopped).

•  Start operation by pressing   button. 
•  When mixing is complete stop the machine by 

pressing   button. 

If during the operation the rack is hold by hand or 
any other external obstacle it automatically stops 
and gives sound alarm. To restart operation press   

 button.

If the machine is not operational and is not dis-
turbed during 10 minutes it automatically goes in to 
energy consumption mode 

SLEEP and shows blink-

ing dots on 

F and RPM displays. To exit SLEEP mode 

either press any button or push the rack with your 
hand a few degrees. By pressing   button twice the 
machine goes out of the 

SLEEP mode and continues 

operation from the same rack position where it was 
stopped. (applies in vortexing programs).

Figure 5

1

4

3

A

B

C

2

Summary of Contents for Inteli-Mixer RM-2













Reviews: