background image

 

 

Technical Support: +44(0)23 9269 6638 (option 3) 

PAK200581_01N October 2015                        ©2015 ELMDENE INTERNATIONAL LTD  

 

C

OMPLIANCE

 

 

 
This power supply unit meets the essential requirements of the  
following EU Directives: 
 

 

 
 
 
 

 

Functional standard:     

EN54-4:1997 +A1 +A2 

    

Environmental Class II  

 

Certification Body:  

    

Underwriters Laboratory 

 
Declaration of Performance: 

DOP2014/06 

  

 

DOP2014/07

 

 

D

ISPOSAL OF 

P

RODUCT AT 

E

ND OF 

L

IFE

 

 

 
This product falls within the scope of EU Directives 2012/19/EU Waste Electrical and Electronic Equipment 
(WEEE)  and  2013/56/EU  (Battery).  At  the  end  of  life,  the  product  must  be  separated  from  the  domestic 
waste stream and disposed via an appropriate approved WEEE disposal route in accordance with all national 
and local regulations. 
Before disposal of the product, any batteries must be removed, and disposed separately via an appropriate 
approved battery disposal route in accordance with all national and local regulations. Package used batteries 
safely for onward transport to your supplier, collection point or disposal facility. 
 

Caution:  Risk of fire or explosion  

if bare battery wires are allowed to touch. 

 
See  Specification  for  battery  type  information.  The  battery  is  marked  with  the  crossed  out  wheelie  bin 
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). 
 

For more information see: 

www.recyclethis.info

 

 
 
 
 
 
 
 
 
 
 

The packaging supplied with this product may be recycled. 

 Please dispose of packaging accordingly. 

 

CPR: 

305/2011 EU 

EMC: 

2014/30/EU

 

Low Voltage: 

2014/35/EU 

WEEE: 

2012/19/EU 

RoHS: 

2011/65/EU 

0843 

 

Elmdene International Ltd 3 Keel Close 

Portsmouth PO35QD 

14 

0843-CPR-0215 

EN54-4:1997 +A1 +A2 

Power Supplies intended for use in fire detection 

and fire alarm systems 

 

Operational reliability

                    - Pass 

 

Durability 

 

 

 

Temperature resistance  

- Pass 

Vibration resistance 

- Pass 

Electrical stability 

- Pass 

Humidity resistance 

- Pass 

Summary of Contents for STX2405-E









Reviews: