background image

3

 

 

 

 

Technical Support: +44(0)23 9269 6638 (option 3) 

  PAK200035_07A   Oct 2014                        ©2014 ELMDENE INTERNATIONAL LTD  

 

 

T

ESTING

 

 

 
 

1) 

Activate bell or ring output from control panel (R- to 0V). Check high volume sound activates. 

2) 

If Lo facility is used, activate keypad on control panel and check low volume from sounder. Adjust VR1 
for desired Lo volume level (see fig 1). 

3) 

Remove cover and check high volume from sounder. (Tamper activation) 

4) 

If Tamper connection is made to the control panel, check that the panel has detected a tamper 
condition from step 4). 

5) 

Replace the cover. Check that the sounder switches off and the tamper output has cleared. 

6) 

INT600S: Remove H+ supply connection at the control panel. Check high volume from sounder and 
tamper is detected at the control panel. 

7) 

INT600S: Replace H+ supply. Check that the sounder switches off and the tamper output has cleared. 

8) 

Fasten the cover to the backplate using the fixing screw supplied. 

 

M

AINTENANCE

 

 

 

This sounder should be tested for correct operation on a periodic basis. A minimum of one check every 12 
months is recommended. The following features should be verified on each maintenance visit:

 

1) 

Correct operation of sounder from control panel signals

 

2) 

Correct operation of cover and rear tampers.

 

3) 

Remove the +ve power supply from the control panel and check internal battery voltage as 
measured between BT+ and BT- is greater than 4.5V dc. If the battery voltage is less than this value 
replace internal battery with similar of 6V 170mAh rating.

 

4) 

Check for signs of significant dust ingress. Clean as necessary.

 

 
 

SAB

 

B

ATTERY 

R

EMOVAL

 

 

 

The SAB battery may be removed for disposal at end of product life. To remove the battery, disconnect 
red and black leads from BT+ and BT- and unclip battery from holder. To fit a new battery, clip into holder 
and reconnect positive (RED) lead to BT+ and negative (BLACK) lead to BT-. 
IMPORTANT: Ensure correct polarity of connections and that exposed battery leads DO NOT accidentally 
touch. 

Dispose of used batteries in accordance with all national and local regulations 

Summary of Contents for INT600

Page 1: ... intensity sound for alarm and an adjustable low level tone for entry exit keypad The INT600 will detect any attempt to gain unauthorised access to the sounder by removal of the cover or any attempt to remove it away from its mounting surface This will generate a tamper signal which is normally fed back to the alarm control panel The INT600 is classified as an internal remote powered sounder and i...

Page 2: ...ent negative hold off supply TR Volt free tamper connection TS Volt free tamper connection BT SAB Battery negative BT SAB Battery positive COMMISSIONING 1 Remove cover 2 Offer backplate to desired position on mounting surface and drill holes to match chosen fixing centres 3 Fix backplate to mounting surface using appropriate fixings for the mounting surface 4 Set the required Cut off Timer using J...

Page 3: ...supplied MAINTENANCE This sounder should be tested for correct operation on a periodic basis A minimum of one check every 12 months is recommended The following features should be verified on each maintenance visit 1 Correct operation of sounder from control panel signals 2 Correct operation of cover and rear tampers 3 Remove the ve power supply from the control panel and check internal battery vo...

Page 4: ...Package used batteries safely for onward transport to your supplier collection point or disposal facility Caution risk of fire or explosion if bare battery wires are allowed to touch See Specification for battery type information The battery is marked with the crossed out wheelie bin symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For more information see www recycl...

Reviews: