background image

page 10

13. Testing Your Fan.

12. Remote Control Operation.

HI

 button - turns 

fan

 to HIGH speed

MED

 button - turns 

fan

 to MEDIUM speed

LOW

 button - turns 

fan

 to LOW speed

REV

 button - used to REVERSE blade direction

 (fan must 

be set on 

low

 

before

 reversing blade direction)

OFF

 button - turns 

fan

 OFF

    button - pushing TOP of button turns 

upper light

 

ON/OFF and pushing BOTTOM of button turns 

lower 

light

 ON/OFF; pressing TOP part of      button and 

holding it down for more than 0.7 seconds converts it 
into a dimmer for the 

upper light

; pressing BOTTOM part 

of      button and holding it down for more than 0.7 
seconds converts it into a dimmer for the 

lower light

It is recommended that you test fan before finalizing 
installation. Restore power from circuit box and light 
switch (if applicable). Locate ON/OFF slider switch on 
wall control and set to the ON position. Test light 
and dimmer function and then test fan speeds. Next, 
locate remote control. Start with the lights OFF and 
test the light ON/OFF function by pressing on the 
upper and then the lower part of the      button. Test 
the dimmer function by pressing the top (and then 
after that the bottom) part of the      button and 
holding it down for 1 second. Test fan speeds with 
the different fan speed buttons. If the remote control 
operates all of the functions of the fan, battery has 
been installed correctly. If the wall and/or remote 
control(s) do (does) not operate all of the fan 
functions, refer to "Troubleshooting" section to solve 
any issues before contacting Customer Service.

Fan 

must

 be on LOW 

before

 setting the fan to reverse 

direction. Use REV button to recirculate air 
depending on the season.

Summary of Contents for CEN54BCH5













Reviews: