manualshive.com logo in svg

Eljen GSF A42, Installation Manual, Page: 28 / 56

Share
Download
Eljen GSF A42 Installation Manual Download Page 28

 

2018 Indiana Design and Installation Manual  

28 

www.eljen.com  

5.0 Elevated Sand Mound Design and Installation 

5.0.1 ACCEPTABLE METHODS OF DISTRIBUTION: 

 Elevated Sand Mounds require pressure distribution. 

 
5.0.2 GENERAL CROSS SECTION 

 

FIGURE 14:  ELEVATED SAND MOUND CROSS SECTION 

 

3

1

NATIVE SOIL

 12" MIN - 19" MAX OF 

COVER SOIL MATERIAL

SPECIFIED SAND

ORIGINAL GRADE

1' BERM

 

 

All elevated sand mound systems are required to have a minimum of: 

 

  12 inches of Specified Sand at the edges of the GSF module. 

  12 inches of Specified Sand at the beginning and end of each GSF Row. 

  12 inches of Specified Sand directly below the GSF module. 

  Minimum 12 inches of cover soil material above the 4-inch distribution pipe  

 

5.0.3 VERTICAL SEPARATION TO SEASONAL HIGH WATER TABLE OR LIMITING LAYER:  

Refer to section 

Rule 410 IAC 6-8.3 72.b.4 for elevated systems or ISDH Rule 410 6-10.1 (61).   

Vertical Separation Distance (VSD)

System Type 

Daily Design Flow 

Limiting 

Layer

Seasonal High Water Table 

Elevated Sand Mound (12” of sand 
under GSF modules and a pressure 
distribution network) 

Any 

20” 

20” 

VSD measured from the existing grade for the elevated sand mound system.

 

5.0.4 ELEVATED SAND MOUND SYSTEM:  

Follow the requirements in 410 IAC 6-8.3 (79) to complete the mound.  

When placing the Eljen application area on the basal area, there must be 12 inches of INDOT SPEC 23 Sand under 
the A42 or B43 Modules.   

 
5.0.5  APPLICATION  AREA  REQUIREMENTS:   

The  application  area  is  the  GSF  Module  and  the  upslope  and 

downslope sand from the module.  Modules may not have more than one foot of sand up or downslope of any 
module.  The maximum distance of the distribution cell edge measured to the module is one foot, and the minimum 
distance to the distribution cell edge is six inches.   

 
5.0.6 PLACEMENT OF THE ELJEN APPLICATION AREA:  

Place the Eljen application area in the middle of the 

basal area for sites with slopes less than 0.5%.  For sites with greater than 0.5% slope, place the Eljen application 
area along the upper edge of the basal area.   

5.0.7 DISPERSAL AREA:  

Dispersal area requirements are located in

 

IAC 6-8.3 (58) or ISDH Rule 410 6-10.1 (62). 

Summary of Contents for GSF A42

























































Reviews:

No comments