Elite Greenhouses 6'3" WIDE HIGH EAVE Instructions & Illustrations Download Page 18 | Manualshive

Page: 18 / 32

background image

FINISHING OFF

To prevent the door from sliding past its opening, you must fix 2 angle brackets to the door end as-
sembly.

Insert a cropped head bolt into the bolt channel at the top of the left hand glazing bar (viewed from
the inside) and fix and angle bracket as shown in the picture below.
The bracket must be fitted at the same height as the door panel so that, as the door moves left or
right, the bracket prevents the door from moving too far along the top door track.
Repeat at the bottom of the door.

«
...
16
17
18
19
20
...
»

Summary of Contents for 6'3" WIDE HIGH EAVE

































Reviews:

No comments

Related manuals for 6'3" WIDE HIGH EAVE

GrowSpan PB01700R4

Brand: FarmTek Pages: 25

Haven HIGH TUNNEL

Brand: Farmers Friend Pages: 44

Growers supply GrowSpan Gothic Pro 113836DD

Brand: FarmTek Pages: 61

Brand: Forest Pages: 4

Brand: G-Tools Pages: 10

6'3" WIDE CRAFTSMAN

Brand: Elite Greenhouses Pages: 28

Brand: Palram Pages: 90

Brand: Palram Pages: 117

POP-UP POLY CAGE Series

Brand: GardenSkill Pages: 2

Brand: Polhus Pages: 39

Brand: Polhus Pages: 40

Pride of the Pacific PLT612SG

Brand: Greenhouse Style Pages: 50

Brand: Greenhouse Style Pages: 51

Five-Wall Series

Brand: Greenhouse Style Pages: 52

Traditional Straight Lean To

Brand: Greenhouse Style Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands