11
The fan will turn ON if the “+” button is pressed and the
hood was OFF.
If the fan is at first speed and the “+” button is pressed,
the fan will be set to second speed.
If the fan is at second speed and the “+” button is pressed,
the fan will be set to third speed.
If the fan is at third speed and the “+” button is pressed,
the fan will be set to fourth speed.
If the fan is at fourth speed and the “+” button is pressed,
a beep will sound.
Clock programming
The clock can be reprogrammed at any time except during
an active timed function.
The clock can be displayed in a twelve hour format and
valid clock times are from 1:00 to 12:59.
The clock can be reprogrammed pressing the “Timer”
button for 3 seconds, and after, the clock can be adjusted
with the “+” and “-” buttons.
The user can have minute increments / decrements of 1
minute, but if the user keep pressing the “+” / ”-” buttons
for more than 1 second, the increments / decrements will
be of 5 minutes.
During this option the control will round to the nearest 5
minutes.
The user can finish on reprogramming the clock pressing
the “Timer” button.
After 1 minute of no button pressed the control will accept the
programmed clock time and will add one minute to the set clock.
Grease filter saturation alarm (Optional)
After thirty fan functional hours, the display will show
“Grease Filter” if the fan is active.
When this icon is shown in the display, the grease filters
installed are required to be washed.
To reset the grease filter saturation alarm the user must
press the “+” button for 5 seconds, after this action the
icon “Grease filter” is not displayed, and the hood has the
normal display operation.
Charcoal filter saturation alarm (Optional)
After one hundred and twenty functional hours of the fan,
the display will show “Charcoal Filter” if the fan is active.
When this icon flashes on display, the charcoal filters
installed are required to be replaced or reactivated.
To reset the charcoal filter saturation indication the user
must press the “-” button for 5 seconds, after this time the
icon “Charcoal filter” is not displayed and the hood has
the normal display operation.
Audible signal activation and deactivation
The audible signals can be activated or deactivated
pressing the “Light” button for 5 seconds.
If the audible signal is activated, a tone must sound and
the “Snd” symbol must appear on the display for 3 seconds.
If the audible signal is deactivated, the “Snd” symbol must
appear on the display for 3 seconds and no tone must
sound.
Charcoal filter inclusion and exclusion (Recirculating
accessories)
The charcoal filter inclusion or exclusion can be set by
pressing the “+” and “-” buttons at the same time for 5
seconds.
The Inclusion or exclusion of charcoal filter must be
selected while the lamps and the motor are OFF.
When the charcoal filter has been excluded, the charcoal
filter alarm is disabled.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Heat sensor
The control is equipped with a heat sensor that will turn
on the blower at third speed if excessive heat occurs
(over 149° F or 65°C) surrounding the control area.
If the blower is OFF or if it is operating at first speed, the
blower will be set automatically to third speed, the display
shows the word “CArE” to indicate that heat sensor has
detected an excessive heat.
During this state, the user may raise the blower speed to
fourth speed but can not decrease the speed.
When the temperature level on the hood drops to normal,
the blower will operate in the setting defined by the user
before the alarm occured.
Maintenance
ATTENTION
!
Before performing any maintenance opera
-
tion, isolate the hood from the electrical supply by switching
off at the connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
Do not spray cleaners directly to the control while cleaning the
Hood.The cooker hood should be cleaned regularly (at least
with the same frequency with which you carry out maintenance
of the fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products.
DO NOT USE ALCOHOL!
WARNING:
Failure to carry out the basic cleaning recommendations of
the cooker hood and replacement of the filters may cause fire risks.
Therefore, we recommend observing these instructions.
The manufacturer declines all responsibility for any damage
to the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
Grease Filter
Traps cooking grease particles.
The filters should be washed frequently using non aggressive
detergents, either by hand or in the dishwasher, which must be
set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
•
•
•
•
