background image

 

  15W0102B300 

 

SINUS PENTA  

PENTA MARINE 

IRIS BLUE 

 

 
 

SAFE TORQUE OFF 

FUNCTION 

- Application Manual -

 

 

 
 
 
Issued on 04/03/2015 
R.00 

 

     
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 

 

 
 
 
 

 

 

 

Elettronica Santerno S.p.A. 

Via della Concia, 7 - 40023 Castel Guelfo (BO) Italia 

Tel. +39 0542 489711  -  Fax +39 0542 489722 

santerno.com

     

[email protected]

 

 This manual is integrant and essential to the product. Carefully read the instructions contained herein 

as they provide important hints for use and maintenance safety. 

  This  device  is  to  be  used  only  for  the  purposes  it  has  been  designed  to.  Other  uses  should  be 

considered improper and dangerous. The manufacturer is not responsible for possible damages caused 
by improper, erroneous and irrational uses. 

 Elettronica Santerno is responsible for the device in its original setting. 

  Any  changes  to  the  structure  or  operating  cycle  of  the  device  must  be  performed  or  authorized  by 

Elettronica Santerno. 

  Elettronica  Santerno  assumes  no  responsibility  for  the  consequences  resulting  by  the  use  of  non-

original spare-parts. 

  Elettronica  Santerno  reserves  the  right  to  make  any  technical  changes  to  this  manual  and  to  the 

device  without  prior  notice.  If  printing  errors  or  similar  are  detected,  the  corrections  will  be  included  in 
the new releases of the manual. 

  The  information  contained  herein  is  the  property  of  Elettronica  Santerno  and  cannot  be  reproduced. 

Elettronica Santerno enforces its rights on the drawings and catalogues according to the law. 

E n g l i s h  

Summary of Contents for IRIS BLUE




























Reviews: