17.6 Setting the end positions and the relief
Important preliminary consideration:
Decide on a specific relief function before setting the end
positions (different combination options according to the
following statements):
This will save unnecessary setting effort!
Press the travel key until the drive signals the transition into
the setting mode, by a short automatic stop. You can now
program the end positions. After setting the two end posi-
tions, the setting mode is completed.
17.6.1 Relief function for the end position(s)
If an end position is set to stop, an additional relief for the
Venetian blind can be released.
Important
Activation of the relief function (in the versions B to D) takes
place in one work step when the end positions are pro-
grammed (see chapter 5.6.7 to chapter 5.6.9)!
17.6.2 Relief function at the upper stop
For variant C (see chapter 5.6.7)
and variant D (see chapter 5.6.8):
Activate relief function at the upper stop.
1
Push and hold the
UP
button ▲ from instruction
①
(chapters 5.6.7 and 5.6.8) and actuate the
DOWN
button ▼ with the assembly cable (at the same time).
Keep both buttons pushed until the Venetian blind
stops.
The relief function at the upper stop is activated.
17.6.3 Relief function at the lower stop
For version C (see chapter 5.6.8)
and version D (see chapter 5.6.9):
Activate relief function at the lower stop
1
Push and hold the
DOWNP
button ▼ from instruction
③
(chapters 5.6.8 and 5.6.9) and actuate the
UP
button ▲ with the assembly cable (at the same time).
Keep both buttons pushed until the Venetian blind
stops.
The relief function at the lower stop is activated.
17.6.4 Changing / Deleting the limit positions
and deleting the discharge function
A change or deletion of a single end position is not possible.
This is always done in pairs (upper and lower end position
simultaneously).
By the deletion of the end positions and the adjustment of
the optional discharge function is lost.
Important
The Venetian blind is adjusted only after a complete and
uninterrupted access and exit to the blind.
Changing / Deleting the end positions
1
From a middle Venetian blind position with the as-
sembly cable , push and hold both direction buttons
(▲ and ▼) at the same time until the drive briefly
moves up and down.
The deletion of the setting of end position is completed.
The end positions can be programmed again.
17.6.5 Four variants of end position settings
Four different combinations of end position settings are
possible. They must be selected sensibly according to the
technical requirements of the Venetian blind.
End position settings
(4 versions)
possible with
A
Upper and lower end posi-
tion freely adjustable
T-strap, tapes,
belt
B
Fixed upper limit stop /
lower end position freely
adjustable
T-strap, tapes,
belt, limit plugs,
angle bracket
C
Fixed upper and lower limit
stop
Anti push-up device,
stiff shaft connector,
limit plugs, angle
bracket
D
Upper end position freely
adjustable, fixed lower limit
stop
Anti push-up device
Fig. 7 Versions of the end position settings in the RolTop
17.6.6 Variant A: Upper and lower end position
freely adjustable
Variant A:
Upper and lower end position freely adjustable
①
From a middle Venetian blind position with the as-
sembly cable, push the
UP
button ▲ until the Vene-
tian blind has reached the desired end position.
The drive starts, stops briefly and then moves on
(while the UP button ▲ is pushed).
Correction is possible with the buttons ▲ and ▼ .
②
Press the AB button ▼ until the drive stops auto-
matically.
The upper end position has been set.
③
Press the
AB
button ▼ again until the Venetian
blind has reached the desired lower end stop.
The drive starts, stops briefly and then moves
on (while the AB button
▼
is pushed).
Correction is possible with the buttons ▲ and ▼ .
④
Press the AUF button
▲
until the drive stops
automatically.
The lower end position has been set.
Setting of the end positions variant A is now complete.
Fig. 8 End position setting Variant A:
©
elero
GmbH
EN | 5
Commissioning | Setting the end positions and the relief
