76
4.5 Operating faults (symptoms, causes and
remedies)
Fault
Cause
Remedy
The equipment does not start. •
Faulty or missing power
supply cable
•
Auxiliary power supply
incorrect (Led MAINS on
the front panel off)
•
Fault on the power supply
stage
•
Replace the power supply
cable and connect it to
the equipment
•
Contact the manufacturer
•
Contact the manufacturer
The equipment does not
reach the required power
•
Equipment in Stand By
mode
•
No jumper for interlock
•
PLL not engaged (ON AIR
warning light on the front
panel off)
•
Power supply fault
•
RF module fault
•
Fault on the power mea-
surement system
•
Put the equipment in RF
ON
•
Insert the jumper for the
interlock
•
Contact the manufacturer
•
Contact the manufacturer
•
Contact the manufacturer
•
Contact the manufacturer
The equipment transmits on a
different frequency from the
one set
•
PLL board failure
•
VCO board failure
•
Contact the manufacturer
•
Contact the manufacturer
Absence of modulation in
output and on display
•
Audio cable interruption
or missing
•
MPX board failure
•
Stereo Coder board failure
•
Modulation is off
•
Audio cable connection or
replacement
•
Contact the manufacturer
•
Contact the manufacturer
•
Reactivate modulation
using the relative menu
Output modulation absent,
but shown on the display
•
MPX board failure
•
Stereo Coder board failure
•
Contact the manufacturer
•
Contact the manufacturer
Output modulation does not
reach the desired value
•
Input audio level low
•
MPX board failure
•
Increase the source audio
level
•
Increase the sensitivity
of the ETG input and/or
contact the manufacturer
Stereophonic modulation
absence
•
Stereophonic carrier off
•
Audio cables interrupted
or missing
•
Stereo Coder board failure
•
Stereo Coder board mis-
sing
•
Turn the stereophonic car-
rier on from the relative
menu
•
Audio cable connection or
replacement
•
Contact the manufacturer
•
The equipment does
not feature the “Stereo
Coder” option, therefore
it cannot be used for ste-
reophonic transmission
One or more fans stopped
•
Fan failure
•
Fan power supply failure
•
Contact the manufacturer
•
Contact the manufacturer
Maintenance
Summary of Contents for ETG2500
