background image

12 / 20

PRE-USE INSTRUCTIONS

WARNING

!

                                            Before using this outdoor fire table, make sure 

you have read, understand and are following all information provided in the 

Important Safety Information section of this manual. Failure to follow those 

instructions can cause death, serious injury or property damage.

Prior to each gas fireplace operation, check the hose and valve for evidence 

of excessive abrasion or wear though the visual check hole on the side of the 

base. Replace visual check cap prior to operating fireplace.

BURNER CONNECTIONS

Make sure the regulator valve and hose connections are securely fastened 

to the burner and the tank. If your unit was assembled for you, visually check 

the connection between the burner pipe and orifice. Make sure the burner 

pipe fits over the orifice.

WARNING

!

Failure to inspect this connection or follow these instructions 

could cause a fire or an explosion. Failure to position the parts 

in accordance with these diagrams or failure to use only parts 

specifically approved with this appliance may result in property 

damage or personal injury.

Please refer to diagram for proper installation.
If the burner pipe does not rest flush to the orifice please
contact 

Elementi at 800-678-7294

 for assistance.

CHECKING FOR LEAKS

Make a leak check solution by mixing 1 part dish
washing soap with 3 parts water in a spray bottle.
Make sure control knob is “OFF.” Then, turn LP gas
tank to “ON” at valve.

Spray leak solution on valve connections paying
particular attention to the areas indicated by arrows.
If any bubbles appear turn LP gas tank OFF, reconnect
and re-test. If you continue to see bubbles after several
attempts, disconnect LP gas source and contact

Elementi at 800-678-7294 

for assistance.

If no bubbles appear after one minute turn tank OFF,
wipe away solution and proceed.

Check for leaks at these locations

Orifice is located
in this connection

Expanded  

View

 

Summary of Contents for OFG105NG





















Reviews: