manualshive.com logo in svg

ElektroPhysik PoroTest 7, Technical Reference And Operating Manual

Share
Download
ElektroPhysik PoroTest 7 Technical Reference And Operating Manual Download Page 16

ElektroPhysik

E-13

Error messages

11. Error Messages

After troubleshooting, all error messages can be quit by pressing ESC. If you press Menu/Enter you
will go back to the main menu.

Error Message

Cause

Remedy

Probe or GND error

Probe connecting or earthing error

Check probe cable for damages.
Connect probe cable properly.
Earth  equipment properly.

Probe connection error

Data communication failure. Connection
between probe and  control unit has been
interrupted during operation.

Check probe cable for damages.
Connect probe cable properly.

Probe voltage drop

Voltage drop between control unit and probe

Recharge battery or switch to mains supply or
attach a shorter connecting cable

Low battery. Please
recharge!

Low battery

Recharge will be necessary soon.

Battery run down. Please
recharge.

Insufficient battery charge

Immediate recharge necessary.

Long bleep - instrument
switches off automatically

Deep discharge protection

Immediate battery discharge necessary.

!

Data have been  changed or deleted from
memory

Please send the instrument  to your dealer for
repair.

Summary of Contents for PoroTest 7

























Reviews:

No comments

Brands by name

Popular brands

Load more brands