1
© 2009, Elektro-Automatik GmbH & Co. KG
EN
Analogue interface
All models feature a 12 pin analogue interface on
the front of the device. It can be used to monitor the
device condition, as well as remotely start/stop the
charging procedure.
Also see next page.
Handling
Powering the device
The device does not feature a power switch. When
connecting it to mains, it is immediately ready to
work.
After switching mains off the device stores the last
state (selected mode, output condition) in order to
restore it automatically at the next start. Thus it can
continue to work after an interruption like a blackout
etc.
Adjusting the output voltage
The nominal output voltage is seperated into three
selectable voltage ranges, each approximately 1/
of the nominal voltage. For details see the „Technical
specifications“.
About the device
Technical specifications
PS 880-40R
PS 880-60R
PS 8360-10R
PS 8360-15R
Mains input
Input voltage
90….264V
90….264V
90….264V
90….264V
Frequency
45….65Hz
45….65Hz
45….65Hz
45….65Hz
Power factor correction
>0.99
>0.99
>0.99
>0.99
Input current at 230V and full load
approx. 4.8A
approx. 7.5A
approx. 4.8A
approx. 7.5A
Input current at 100V and full load
approx. 11.4A
approx. 11.4A
approx. 11.4A
approx. 11.4A
Output - Voltage
Nominal voltage U
Nom
80V
80V
360V
360V
Voltage range 1
0V...30V
0V...30V
0V...120V
0V...120V
Voltage range 2
30V...60V
30V...60V
120V...240V
120V...240V
Voltage range 3
60V...80V
60V...80V
240V...360V
240V...360V
Stability at 10-90% load
<0.05%
<0.05%
<0.05%
<0.05%
Stability at ±10%
¨
U
In
<0.02%
<0.02%
<0.02%
<0.02%
Ripple
<70mV
PP
<70mV
PP
<100mV
PP
<100mV
PP
Regulation 10-100% load
<2ms
<2ms
<2ms
<2ms
Output - Current
Nominal current
40A
60A
10A
15A
Stability at 0-100%
¨
U
Out
<0.15%
<0.15%
<0.15%
<0.15%
Stability at ±10%
¨
U
In
<0.05%
<0.05%
<0.05%
<0.05%
Ripple
<100mA
PP
<100mA
PP
<15mA
PP
<15mA
PP
Output - Power
Nominal power
1000W
1500W
1000W
1500W
Nominal power at U
In
<150V
1000W
1000W
1000W
1000W
Miscellaneous
Operation temperature
0….40°C
0….40°C
0….40°C
0….40°C
Storage temperature
-20….70°C
-20….70°C
-20….70°C
-20….70°C
Humidity
<80%
<80%
<80%
<80%
Dimensions (WxHxD)
90x360x240mm
90x360x240mm
90x360x240mm
90x360x240mm
Weight
8.9kg
9.2kg
8.9kg
9.2kg
Article No.
21540107
21540108
21540109
21540110
Safety
EMC standards
Overvoltage category
Protection class
EN 60950
EN 61204, EN 55022 Class B
Class II
Class I
The built-in trimmer is a 10-turn type and the ap-
proximate 10 rotations from left stop to right stop
correspond to the selected range.
Switching output on or off
The pushbutton „On/Off“ is used to switch the power
output on or off, if not inhibited by any error (OVP or
OT) or the device being in remote control. The voltage
set by the trimmer will then be put out immediately.
The output can also be switched off at any time via
pin 8 „Rem-SB“ of the analogue interface and then
on again.
Attention! The pin REM-SB overrides the pushbutton
„On/Off“.
When the output is switched on, the LED „CC“ will
indicate constant current operation (LED is on) or
constant voltage operation (LED is off).
Selecting a voltage range
The pushbutton „Output Range“ is used to select the
output voltage ranges. The output has to be off in
order to select the voltage range.
