manualshive.com logo in svg

Elekitsorparts FAA-450, Operation Manual

Share
Download
Elekitsorparts FAA-450 Operation Manual Download Page 21

Elekitsorparts Store Item Name: FAA-450_EU1KY_Antenna Analyzer

Item No.: H10010

Document Type: Manual

21

R0

50

Base Z0 for VSWR measurements and Gamma calculation

OSL_RLOAD

50

OSL calibration standard for the Load measurement, Ohm

OSL_RSHORT

5

OSL calibration standard for the Short measurement, Ohm uint32_t

ROPEN

500

OSL calibration standard for the Open measurement, Ohm. Use
value >100000 for purely open load.

OSL_NSCANS

1

Number of scans to average during OSL calibration

MEAS_NSCANS

1

Number of scans to average in measurement window

PAN_NSCANS

1

Number of scans to average in panoramic window

LIN_ATTENUATION

6

Linear audio input attenuation. Applied during audio input device
initialization after reset. Sets the linear audio input volume to (100 -
ATTENUATION). One unit is approximately 1 dB.

F_LO_DIV_BY_TWO

0

Deprecated, references in the code have been removed. Leave at
default setting (0). Set to non zero if LO frequency is divided by two
in quadrature mixer. Intended to be used with obsolete version 2 RF
front end.

GEN_F

14000000

Frequency for generator window, Hz

PAN_CENTER_F

0

Way of setting panoramic window. 0: F0+band_span, 1: F_/-
Band_span/2

BRIDGE_RM

5.1

Value of measurement resistor (R4, R11) in bridge, Ohm

float

BRIDGE_RADD

200

Value of series resistor (R5, R9) in bridge, Ohm

BRIDGE_RLOAD

51

Value of load resistor in bridge (R7, R10), Ohm

COM_PORT

0

Serial (COM) port to be used: 0 for COM1, 1 for COM2

COM_SPEED

38400

Serial (COM) port speed, bps

LOWPWR_TIME

0

Time in milliseconds after which to lower power consumption by
switching off LCD. (0 - disabled)

3RD_HARMONIC_E

NABLED

0

Deprecated, references in the code have been removed. Leave at
default setting. (1) Enable, above BAND_FMAX to extend
frequency range to 450 MHz. (0) Disables. Support is not fully
implemented yet.

S11_SHOW

0

Reflection S11 (module in dB) graph in the panoramic window: 1
enabled, 0 disabled

S1P_TYPE

0

Type of Touchstone S1P file saved with panoramic screen shot: 0 - S
MA R 50, 1 - S RI R 50.

SHOW_HIDDEN

0

1: Show hidden options in configuration menu. 0: hide.

SCREENSHOT_FOR

MAT

0

Screen shot image file format. 1: PNG, 0: BMP.

BAND_FMAX

150000000

Maximum operating frequency of the device, Hz. Must be a multiple
of 100000, and not above 450000000.

SI5351_MAX_FREQ

160000000

Maximum frequency in Hz that Si5351a can reliably output. Can be
160MHz or 200 MHz.

SI5351_CAPS

3

Si5351 built-in quartz capacitors setting. 1 for 6pF, 2 for 8pF, 3 for
10 pF

TDR_VF

66

Velocity factor for TDR distance calculation, percent (valid range
1..100)

Summary of Contents for FAA-450

























Reviews:

No comments

Brands by name

Popular brands

Load more brands