MANUAL CODE: XXXXX
PROFESSIONAL SOUS COOKER
ISSUE DATE: 15/01/2018 vers_00_05
Rev. 00.00 WITH REFERENCE TO FIRMWARE VERSION :00_15 and more
ELE
GEN
by Quaglia Luigi - Via Jmre Nagy 8-8/A 42019 - Scandiano Reggio Emilia Italy- VAT No. 02018620357
TEL.+390522859721 – FAX +390522767677 -
VOIP Skype. eleg2002
- Web-www.elegen.it - email
Page 11 of 16
mixer.
Attention !!
do not use dense products, with cream or containing pieces of food.
To access the various functions, proceed as follows:
1)
Press the
fn
key to activate the
fn on
led, and the message will appear on the first menu
Auto Start-,
press the
fn
key
to go to the next menu, press the
Ok
key to access this menu and use the automatic start function. If you continue
pressing the
fn
key you go to the next function and the message displayed will be
LIVE TENPER, pressing the fn
key again
you access the circulator function and the
CIRCULATOR OFF
message will be displayed, pressing the
fn
key again you exit the fn function menu and the
fn on
led will switch off.
Activate the
Auto Start-
function
1)
Press the
fn
key until the
fn on
led switches on
2)
When the
Auto Start-
message is displayed, press the
OK
key to confirm the choice
3)
The timer variation of auto start is proposed, with the hours flashing, if you want to change the hours press the
+ or –
keys of the Timer dial and confirm pressing the
OK
key, otherwise pressing only the
OK
key the minutes variation is
proposed, to change proceed as before. If no key is pressed, after approx. 30 seconds the cycle will start with the pre-
set time.
At the end of setting, the work cycle will start and the message
XX.XX
(value of time set) will be displayed
AUTO on
in the following digits. After approx. 1 minute, the display will switch off to protect consumption and the signs ------
- will pass in sequential manner every 2 seconds, to indicate the SOUS COOKER is counting. You can display the status at any
time by pressing any key. To stop the auto start cycle, activate the display if with the continuous signs --- and press the
ESC
key or
fn
key.
Two minutes before expiry of the auto start time, the display will automatically light up to indicate the remaining time on cycle
start-up, on expiry of the time, it will automatically start based on the previously selected program.
Attention!! During the Auto Start timer setting, do not set the time on Infino
00
00 or on timer disabled ---- otherwise the
auto start function will be disabled
LIVE
function activation,
1)
Press the fn key until the fn on led switches on
2)
Press the fn key again to display the message
LIVE TENPER
3)
Press the
Ok
key to confirm the function selection
The following message appears on the display: LIVE XXX XXX; ( XXX temperatures value), in this position the temperatures
will be displayed for an uncertain amount of time and until the user requires it.
CIRCULATOR
function activation,
1)
Press the fn key until the fn on led switches on
2)
Press the fn key again to display the message -
CIRCULoFF
3)
Press the + key on the probe at the heart dial to switch on the circulator
4)
Press the - key on the probe at the heart dial to switch off the circulator
To start the speed
5)
Press the
Circulator
key
6)
Vary the speed using the + or – keys of the probe at the heart
During variation of the speed, the message
SPEDSET XX (xx speed set) will appear
With + and – of the probe at the heart dial, vary the speed, after a few seconds of not pressing buttons the display will show
The message
CIRC XXX XXX
; (XXX real temperatures).
To exit, press the ESC key or the fn key twice
7.6 STANDBY
If you do not use the machine for a period of 5 consecutive minutes, the STANDBY function is enabled. In this case, the On
Standby led will be flashing, this function is used to reduce consumption to a minimum, avoiding pointless waste and
safeguarding the environment.
To re-activate the machine and exit the Standby status, proceed as follows:
1)
Press the Start / Stop / Esc key
2)
Release the key
When the standby function is reactivated, the position is proposed where you were before standby, therefore if SOUS COOKER
was not in the work cycle Standby is re-proposed, otherwise it is indicated if the cycle has terminated due to an alarm or cycle
end. To restore SOUS COOKER, you need to press a key again.
Attention !!
if the machine is in standby and the switch on the back is turned off, you need to wait at least 10 seconds before
switching back on the switch until the control is available.
